Home › Vehicle Exterior › DOOR / HATCH › FUEL LID OPENER MOTOR ASSEMBLY

FUEL LID OPENER MOTOR ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL FUEL FILLER OPENING LID LOCK RETAINER


    B262230
  1. Install the fuel filler opening lid lock retainer and turn it counterclockwise as shown in the illustration.
    Text in Illustration 
    V100135
    Push
    V100136
    Turn



2. INSTALL FUEL LID WITH MOTOR LOCK ASSEMBLY
  1. Connect the connector.

  1. Engage the clip and guide.

  1. Install the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    B262228E01
  1. Install the cable and turn it clockwise as shown in the illustration.
    Text in Illustration 
    *a
    Yellow Mark
    V100135
    Push
    V100136
    Turn

    HINT:
    Connect the cable with its yellow mark toward the inside of the vehicle.



3. INSTALL W/ BOX NO. 1 SPEAKER ASSEMBLY (for 14 Speakers)


    E161046
  1. Install the w/box No. 1 speaker with the 4 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the connector.



4. INSTALL QUARTER TRIM PANEL ASSEMBLY LH (for Manual Seat)
  1. Connect the connector.

  1. Attach the 11 clips to install the quarter trim panel.

  1. Install the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



  1. Install the 2 clips.


    B222458



    B193068
  1. Attach the 2 claws to install the cover.



    B191816
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B191818
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B193920
  1. Attach the 3 claws to install the outer lap belt anchor cover.



5. INSTALL QUARTER TRIM PANEL ASSEMBLY LH (for Power Seat)
  1. Connect the 5 connectors.

  1. Attach the 11 clips to install the quarter trim panel.

  1. Install the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. Attach the 2 clamps to install the wire harness.



  1. Install the 2 clips.


    B222460



    B193068
  1. Attach the 2 claws to install the cover.



    B191816
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B191818
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B193920
  1. Attach the 3 claws to install the outer lap belt anchor cover.



6. INSTALL REAR FLOOR MAT SUPPORT PLATE


    B190142
  1. Attach the 5 clips and 4 claws to install the rear floor mat support plate.



7. INSTALL ROPE HOOK ASSEMBLY


    B190141
  1. Install the rope hook with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    B190139
  1. Attach the 2 claws to install the cover.



8. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure for both sides.



9. INSTALL REAR DOOR SCUFF PLATE LH

HINT:
Use the same procedure for both sides.



10. INSTALL REAR FLOOR STEP NO. 1 COVER


    B191404
  1. Attach the 2 claws to install the rear floor step No. 1 cover.



11. INSTALL REAR FLOOR STEP NO. 2 COVER


    B193890
  1. Attach the 2 claws to the install the rear floor step No. 2 cover.



12. INSTALL REAR SEAT CUSHION HINGE LOWER COVER LH

HINT:
Use the same procedure for both sides.



13. INSTALL REAR NO. 2 SEAT ASSEMBLY LH (for Manual Seat)
(Click here)


14. INSTALL REAR NO. 2 SEAT ASSEMBLY LH (for Power Seat)
(Click here)