Home › Vehicle Interior › SEAT › POWER SEAT CONTROL ECU (for LH Side)

POWER SEAT CONTROL ECU (for LH Side) > INSTALLATION

for Preparation Click here



1. INSTALL FOLD SEAT CONTROL ECU


    B194055
  1. Install the fold seat control ECU with the 2 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the 2 connectors.



2. INSTALL W/ BOX NO. 1 SPEAKER ASSEMBLY (for 14 Speakers)


    E161046
  1. Install the w/box No. 1 speaker with the 4 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the connector.



3. INSTALL QUARTER TRIM PANEL ASSEMBLY LH (for Manual Seat)
  1. Connect the connector.

  1. Attach the 11 clips to install the quarter trim panel.

  1. Install the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



  1. Install the 2 clips.


    B222458



    B193068
  1. Attach the 2 claws to install the cover.



    B191816
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B191818
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B193920
  1. Attach the 3 claws to install the outer lap belt anchor cover.



4. INSTALL QUARTER TRIM PANEL ASSEMBLY LH (for Power Seat)
  1. Connect the 5 connectors.

  1. Attach the 11 clips to install the quarter trim panel.

  1. Install the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. Attach the 2 clamps to install the wire harness.



  1. Install the 2 clips.


    B222460



    B193068
  1. Attach the 2 claws to install the cover.



    B191816
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B191818
  1. Install the outer lap belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B193920
  1. Attach the 3 claws to install the outer lap belt anchor cover.



5. INSTALL REAR FLOOR MAT SUPPORT PLATE


    B190142
  1. Attach the 5 clips and 4 claws to install the rear floor mat support plate.



6. INSTALL ROPE HOOK ASSEMBLY


    B191405
  1. Install the rope hook with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    HINT:
    Use the same procedure for both sides.



7. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure for both sides.



8. INSTALL REAR DOOR SCUFF PLATE LH

HINT:
Use the same procedure for both sides.



9. INSTALL REAR FLOOR STEP NO. 1 COVER


    B191404
  1. Attach the 2 claws to install the rear floor step No. 1 cover.



10. INSTALL REAR FLOOR STEP NO. 2 COVER


    B193890
  1. Attach the 2 claws to the install the rear floor step No. 2 cover.



11. INSTALL REAR SEAT CUSHION HINGE LOWER COVER LH

HINT:
Use the same procedure for both sides.



12. INSTALL REAR NO. 2 SEAT ASSEMBLY LH (for Power Seat)
  1. Install the rear No. 2 seat assembly LH (Click here).