Home › Vehicle Exterior › DOOR / HATCH › FUEL LID OPENER MOTOR ASSEMBLY

FUEL LID OPENER MOTOR ASSEMBLY > REMOVAL

for Preparation Click here



1. REMOVE REAR NO. 2 SEAT ASSEMBLY LH (for Manual Seat)
(Click here)


2. REMOVE REAR NO. 2 SEAT ASSEMBLY LH (for Power Seat)
(Click here)


3. REMOVE REAR SEAT CUSHION HINGE LOWER COVER LH

HINT:
Use the same procedure for both sides.



4. REMOVE REAR FLOOR STEP NO. 1 COVER


    B191403E01
  1. Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the cap.

    HINT:
    Use the same procedure for both sides.



5. REMOVE REAR FLOOR STEP NO. 2 COVER


    B193052E01
  1. Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the cap.

    HINT:
    Use the same procedure for both sides.



6. REMOVE REAR DOOR SCUFF PLATE LH

HINT:
Use the same procedure for both sides.



7. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure for both sides.



8. REMOVE ROPE HOOK ASSEMBLY

HINT:
Use the same procedure for both sides.



    B190140E01
  1. Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the cover.



    B190141
  1. Remove the bolt and the rope hook.



9. REMOVE REAR FLOOR MAT SUPPORT PLATE


    B190142
  1. Detach the 5 clips and 4 claws, and remove the rear floor mat support plate.



10. REMOVE QUARTER TRIM PANEL ASSEMBLY LH (for Manual Seat)


    B193920
  1. Detach the 3 claws and remove the outer lap belt anchor cover.



    B191818
  1. Remove the bolt and outer lap belt anchor.



    B191816
  1. Remove the bolt and outer lap belt anchor.



    B191817E01
  1. Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the cover.

  1. Remove the 2 bolts and 2 clips.

  1. Detach the 11 clips.



  1. Disconnect the connector and remove the quarter trim panel.


    B222458



11. REMOVE QUARTER TRIM PANEL ASSEMBLY LH (for Power Seat)


    B193920
  1. Detach the 3 claws and remove the outer lap belt anchor cover.



    B191818
  1. Remove the bolt and outer lap belt anchor.



    B191816
  1. Remove the bolt and outer lap belt anchor.



    B191817E01
  1. Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the cover.

  1. Remove the 2 bolts and 2 clips.

  1. Detach the 2 clamps and remove the wire harness.

  1. Detach the 11 clips and 2 clamps.



  1. Disconnect the 5 connectors and remove the quarter trim panel.


    B222460



12. REMOVE W/ BOX NO. 1 SPEAKER ASSEMBLY (for 14 Speakers)


    E161046
  1. Disconnect the connector.

  1. Remove the 4 bolts and the w/box No. 1 speaker.



13. REMOVE FUEL LID WITH MOTOR LOCK ASSEMBLY


    B262227
  1. Turn the cable counterclockwise and disconnect the cable from the fuel filler opening lid lock retainer.
    Text in Illustration 
    V100135
    Turn
    V100136
    Pull Out



    B262231
  1. Remove the bolt.



    B262232
  1. Disengage the clip and guide.

  1. Disconnect the connector and remove the fuel lid with motor lock assembly.



14. REMOVE FUEL FILLER OPENING LID LOCK RETAINER


    B262229
  1. Turn the fuel filler opening lid lock retainer clockwise and remove the fuel filler opening lid lock retainer.
    Text in Illustration 
    V100135
    Turn
    V100136
    Pull Out