DTC B15C3 Speaker Output Short |
| DTC Code | DTC Detection Condition | Trouble Area |
| B15C3 | A short is detected in the speaker output circuit. |
|

| 1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - SPEAKERS) |
Disconnect the connectors from the navigation receiver assembly and speakers.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I41-1 (FR+) - L8-1 | Always | Below 1 Ω |
| I41-5 (FR-) - L8-2 | Always | Below 1 Ω |
| I41-1 (FR+) - I11-3 (TWR+) | Always | Below 1 Ω |
| I41-5 (FR-) - I11-4 (TWR-) | Always | Below 1 Ω |
| I41-2 (FL+) - M10-1 | Always | Below 1 Ω |
| I41-6 (FL-) - M10-2 | Always | Below 1 Ω |
| I41-2 (FL+) - I13-3 (TWL+) | Always | Below 1 Ω |
| I41-6 (FL-) - I13-4 (TWL-) | Always | Below 1 Ω |
| I42-1 (RR+) - N1-1 | Always | Below 1 Ω |
| I42-3 (RR-) - N1-2 | Always | Below 1 Ω |
| I42-1 (RR+) - O37-1 (+) | Always | Below 1 Ω |
| I42-3 (RR-) - O37-2 (-) | Always | Below 1 Ω |
| I42-2 (RL+) - N7-1 | Always | Below 1 Ω |
| I42-6 (RL-) - N7-2 | Always | Below 1 Ω |
| I42-2 (RL+) - O31-1 (+) | Always | Below 1 Ω |
| I42-6 (RL-) - O31-2 (-) | Always | Below 1 Ω |
| I41-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| I41-5 (FR-) - Body ground | Always | 10 kΩ or higher |
| I41-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| I41-6 (FL-) - Body ground | Always | 10 kΩ or higher |
| I42-1 (RR+) - Body ground | Always | 10 kΩ or higher |
| I42-3 (RR-) - Body ground | Always | 10 kΩ or higher |
| I42-2 (RL+) - Body ground | Always | 10 kΩ or higher |
| I42-6 (RL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 2.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY |
![]() |
Disconnect the front No. 1 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Always | 3.2 to 4.8 Ω |
|
| ||||
| OK | |
| 3.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY |
![]() |
Disconnect the front No. 2 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 (TWL+) - 1 (+) | Always | Below 1 Ω |
| 4 (TWL-) - 2 (-) | Always | Below 1 Ω |
| 3 (TWL+) - 4 (TWL-) | Always | 3.4 to 4.6 Ω |
| Tester Connection | Condition | Specified Condition |
| 3 (TWR+) - 1 (+) | Always | Below 1 Ω |
| 4 (TWR-) - 2 (-) | Always | Below 1 Ω |
| 3 (TWR+) - 4 (TWR-) | Always | 3.4 to 4.6 Ω |
| *A | for LH Side |
| *B | for RH Side |
|
| ||||
| OK | |
| 4.INSPECT FRONT NO. 3 SPEAKER ASSEMBLY |
![]() |
Disconnect the front No. 3 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 3 | Always | 4 Ω |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER ASSEMBLY - FRONT NO. 3 SPEAKER ASSEMBLY) |
Disconnect the I13*1 and/or I11*2 front No. 2 speaker assembly connector.
Disconnect the M1*1 and/or L1*2 front No. 3 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I13-1 (+) - M1-3 | Always | Below 1 Ω |
| I13-2 (-) - M1-1 | Always | Below 1 Ω |
| I13-1 (+) - Body ground | Always | 10 kΩ or higher |
| I13-2 (-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| I11-1 (+) - L1-3 | Always | Below 1 Ω |
| I11-2 (-) - L1-1 | Always | Below 1 Ω |
| I11-1 (+) - Body ground | Always | 10 kΩ or higher |
| I11-2 (-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 6.INSPECT QUARTER SIDE SPEAKER ASSEMBLY |
![]() |
Disconnect the quarter side speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (+) - 3 (+) | Always | Below 1 Ω |
| 2 (-) - 4 (-) | Always | Below 1 Ω |
| 1 (+) - 2 (-) | Always | 4 Ω |
|
| ||||
| OK | |
| 7.INSPECT REAR NO. 2 SPEAKER ASSEMBLY |
![]() |
Disconnect the rear No. 2 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 3 | Always | 4 Ω |
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (QUARTER SIDE SPEAKER ASSEMBLY - REAR NO. 2 SPEAKER ASSEMBLY) |
Disconnect the O31*1 and/or O37*2 quarter side speaker assembly connector.
Disconnect the N8*1 and/or N2*2 rear No. 2 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O31-3 (+) - N8-3 | Always | Below 1 Ω |
| O31-4 (-) - N8-1 | Always | Below 1 Ω |
| O31-3 (+) - Body ground | Always | 10 kΩ or higher |
| O31-4 (-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| O37-3 (+) - N2-3 | Always | Below 1 Ω |
| O37-4 (-) - N2-1 | Always | Below 1 Ω |
| O37-3 (+) - Body ground | Always | 10 kΩ or higher |
| O37-4 (-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 9.INSPECT REAR NO. 1 SPEAKER ASSEMBLY |
![]() |
Disconnect the rear No. 1 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Always | 4 Ω |
|
| ||||
| OK | ||
| ||