Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM

BLIND SPOT MONITOR SYSTEM > FREEZE FRAME DATA

for Preparation Click here



FREEZE FRAME DATA
  1. Whenever a DTC is stored, the blind spot monitor sensor stores the current vehicle (sensor) state as Freeze Frame Data.


CHECK FREEZE FRAME DATA
  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Blind Spot Monitor Master or Blind Spot Monitor Slave / Trouble Codes.

  5. According to the display on the intelligent tester, select the trouble code data display with Freeze Frame Data.

    Blind Spot Monitor Master 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Turn Switch State
    Master side, slave side state of the turn switch / Master ON, Slave ON or OFF
    Master ON: Right turn switch on
    Slave ON: Left turn switch on
    OFF: Switch not operated
    -
    Master Side Turn Signal
    State of the master side turn signal / OFF or ON
    ON: Right turn signal received
    OFF: Right turn signal not received
    -
    Reverse
    State of the shift position R signal / OFF or ON
    ON: Shift lever in R
    OFF: Shift lever in any position except R
    -
    Vehicle Speed
    Vehicle speed signal / Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph)
    Vehicle stopped: 0 km/h (0 mph)
    -
    Steering Angle
    Steering angle sensor / Min.: -3072°, Max.: 3070.5°
    Left turn: Increases
    Right turn: Decreases
    -
    VGRS Relative Angle
    Compensation value of steering angle calculated by VGRS / Min.: -8.192 rad, Max.: 8.191 rad
    Left turn: Increases
    Right turn: Decreases
    This item is only for vehicles with the VGRS system.
    Power Supply Voltage
    Power supply voltage / Min.: 0 V, Max.: 50 V
    11 to 14 V
    -
    BSM Warning Indicator Turning on (Master)
    Blind spot monitor indicator RH illumination state / OFF or ON
    OFF: Except below
    1. ON: All of following conditions met
      1. Initial check not being performed
      2. Vehicle detected in right side warning area
      3. Right turn signal off
      4. Vehicle speed 40 km/h (25 mph) or more
      5. Shift lever not in R
      6. Blind spot monitor system warning message not displayed
    -
    BSM Warning Indicator Flashing (Master)
    Blind spot monitor indicator RH flashing state / OFF or ON
    OFF: Except below
    1. ON: All of following conditions met
      1. Initial check not being performed
      1. Vehicle detected in right side warning area
      1. Right turn signal on
      1. Vehicle speed 40 km/h (25 mph) or more
      1. Shift lever not in R
      1. Blind spot monitor system warning message not displayed
    -

    Blind Spot Monitor Slave 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Turn Switch State
    Master side, slave side state of the turn switch / Master ON, Slave ON or OFF
    Master ON: Right turn switch on
    Slave ON: Left turn switch on
    OFF: Switch not operated
    -
    Slave Side Turn Signal
    State of the slave side turn signal / OFF or ON
    ON: Left turn signal received
    OFF: Left turn signal not received
    -
    Reverse
    State of the shift position R signal / OFF or ON
    ON: Shift lever in R
    OFF: Shift lever in any position except R
    -
    Vehicle Speed
    Vehicle speed signal / Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph)
    Vehicle stopped: 0 km/h (0 mph)
    -
    Steering Angle
    Steering angle sensor / Min.: -3072°, Max.: 3070.5°
    Left turn: Increases
    Right turn: Decreases
    -
    VGRS Relative Angle
    Compensation value of steering angle calculated by VGRS / Min.: -8.192 rad, Max.: 8.191 rad
    Left turn: Increases
    Right turn: Decreases
    This item is only for vehicles with the VGRS system.
    Power Supply Voltage
    Power supply voltage / Min.: 0 V, Max.: 50 V
    11 to 14 V
    -
    BSM Warning Indicator Flashing (Slave)
    Blind spot monitor indicator LH illumination state / OFF or ON
    OFF: Except below
    1. ON: All of following conditions met
      1. Initial check not being performed
      2. Vehicle detected in left side warning area
      3. Left turn signal off
      4. Vehicle speed 40 km/h (25 mph) or more
      5. Shift lever not in R
      6. Blind spot monitor system warning message not displayed
    -
    BSM Warning Indicator Flashing (Slave)
    Blind spot monitor indicator LH flashing state / OFF or ON
    OFF: Except below
    1. ON: All of following conditions met
      1. Initial check not being performed
      2. Vehicle detected in left side warning area
      3. Left turn signal on
      4. Vehicle speed 40 km/h (25 mph) or more
      5. Shift lever not in R
      6. Blind spot monitor system warning message not displayed
    -


CLEAR FREEZE FRAME DATA

NOTICE:
Clearing the DTCs will also clear the Freeze Frame Data.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Clear the DTCs and Freeze Frame Data.