Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type)

AUDIO AND VISUAL SYSTEM (for Radio and Display Type) > OPERATION CHECK

for Preparation Click here



CHECK PANEL & STEERING SWITCH

HINT:
  1. The radio and display receiver assembly panel switches are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).



  2. E268454
  3. Select "Function Check/Setting" from the "Service Menu" screen.



  4. E302047
  5. Select "Panel&Steering Switch" from the "Function Check/Setting I" screen.



  6. Panel & Steering Switch Check Mode



      E225786E01
    1. Operate each switch and check that the number of switches pushed and the switch conditions are correctly displayed.
      Screen Description 
      Display
      Content
      *a: Switch condition
      "Pushed" is displayed when any switch is pushed
      *b: Number of pushed switch
      1. Number of switches pushed at once is displayed
      2. If more than 3 switches are pushed at once, "More than 3" is displayed
      *c: Rotary switch direction
      Direction of rotary switch is displayed

      NOTICE:
      When the "MENU" switch is pressed and held for 3 seconds or more, diagnostic mode will be canceled.


CHECK TOUCH SWITCH

HINT:
  1. The touch switches on the screen are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).



  2. E268454
  3. Select "Function Check/Setting" from the "Service Menu" screen.



  4. E302043
  5. Select "Touch Switch" from the "Function Check/Setting I" screen.



  6. E176521
  7. Touch Switch Check

    1. Touch the display anywhere in the open area to perform the check when the "Touch Switch Check" screen is displayed.

      HINT:
      1. A "+" mark is displayed where the display is touched.
      2. The "+" mark remains on the display even after the finger is removed.


CHECK MICROPHONE

HINT:
  1. The microphone and microphone input level are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).



  2. E268454
  3. Select "Function Check/Setting" from the "Service Menu" screen.



  4. E302044
  5. Select "Microphone Check" from the "Function Check/Setting I" screen.



  6. Microphone and Voice Recognition Check



      E268457E08
    1. When speaking into the microphone, check that the microphone input level meter changes according to the input level.
      Screen Description 
      Display
      Content
      *a: Microphone input level meter
      Monitors the microphone input level every 0.1 seconds and displays the results in 8 different levels


CHECK VEHICLE SIGNAL

HINT:
  1. Vehicle signals received by the radio and display receiver assembly are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).



  2. E268454
  3. Select "Function Check/Setting" from the "Service Menu" screen.



  4. E302045
  5. Select "Vehicle Signal" from the "Function Check/Setting I" screen.



  6. Vehicle Signal Check Mode



      E286167
    1. When the "Vehicle Signal Check Mode" screen is displayed, check all the vehicle signal conditions.
      Screen Description 
      Display
      Content
      Battery
      Battery voltage is displayed
      IG
      Ignition switch ON/OFF state is displayed
      PKB
      Parking brake ON/OFF state is displayed
      REV
      Reverse signal ON/OFF state is displayed
      SPEED
      Vehicle speed is displayed in km/h
      TAIL
      Tail signal (light control switch) ON/OFF state is displayed

      HINT:
      1. Only items sending vehicle signals will be displayed.
      2. This screen displays vehicle signals received by the radio and display receiver assembly.
      3. This screen is updated once per second.


CHECK HF VOICE QUALITY SETTING

HINT:
  1. The hands-free voice of a "Bluetooth" compatible phone can be adjusted using the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).



  2. E268454
  3. Select "Function Check/Setting" from the "Service Menu" screen.



  4. E302046
  5. Select "HF Voice Quality Setting" from the "Function Check/Setting I" screen.



  6. E268475E01
  7. Hands-Free Voice Quality Setting
    Text in Illustration 
    *a
    Numeric keypad
    *b
    Setting button
    *c
    Reset button

    NOTICE:
    Sound quality may deteriorate when the receive voice level is changed more than necessary. For this reason, check that the received voice quality is still acceptable after changing this setting.


    1. If necessary, refer to the table below to adjust the voice quality type with the numeric keypad.

    2. When adjusting the settings, use the number pad on the screen to input the voice quality type according to the table.

      Settings 
      Parameter
      Target Phenomenon
      Voice Quality Type
      Effect of Changing Voice Quality
      Negative Effect of Changing Voice Quality
      A
      (Noise)
      The other party hears background noise when listening to your voice
      1000
      The amount of background noise the other party hears when listening to your voice is reduced
      The volume of voice the other party hears when listening to your voice may temporarily drop
      B
      (Noise)
      The other party hears a lot of background noise when listening to your voice
      2000
      The amount of background noise the other party hears when listening to your voice is sharply reduced.
      The volume of voice the other party hears when listening to your voice may temporarily drop.
      C
      (Echo)
      The other party hears weak echoes
      0100
      The amount of echo is reduced (low level)
      Sound quality of the other party deteriorates (low level)
      D
      (Echo)
      The other party hears strong echoes
      0200
      The amount of echo is reduced (high level)
      Sound quality of the other party deteriorates (high level)

      Settings (When Multiple Phenomena Occurred) 
      Parameter
      Target Phenomenon
      Voice Quality Type
      Effect of Changing Voice Quality
      Negative Effect of Changing Voice Quality
      A+C
      The other party hears background noise and weak echoes when listening to your voice
      1100
      1. The amount of background noise the other party hears when listening to your voice is reduced
      2. The amount of echo is reduced (low level)
      1. The volume of voice may drop temporarily
      2. Sound quality of the other party deteriorates (low level)
      A+D
      The other party hears background noise and strong echoes when listening to your voice
      1200
      1. The amount of background noise the other party hears when listening to your voice is reduced
      2. The amount of echo is reduced (high level)
      1. The volume of voice may drop temporarily
      2. Sound quality of the other party deteriorates (high level)
      B+C
      The other party hears a lot of background noise and weak echoes when listening to your voice
      2100
      1. The amount of background noise the other party hears when listening to your voice is sharply reduced
      2. The amount of echo is reduced (low level)
      1. The volume of voice may drop temporarily
      2. Sound quality of the other party deteriorates (low level)
      B+D
      The other party hears a lot of background noise and strong echoes when listening to your voice
      2200
      1. The amount of background noise the other party hears when listening to your voice is sharply reduced
      2. The amount of echo is reduced (high level)
      1. The volume of voice may drop temporarily
      2. Sound quality of the other party deteriorates (high level)

      HINT:
      1. The default value is "0000".
      2. Settings will be applied when the setting button is selected.
      3. If voice quality type values that are not in the table are input, the setting will not be applied and a positive effect may not be gained.
      4. If the quality of phone calls decreases due to the changed settings, return the settings to "0000" by pressing the "INIT" switch.


CHECK SPEAKER
  1. This function is used when checking the speaker wiring and whether the speakers are functioning properly.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.
  1. Turn audio mode on and play any audio source.

    HINT:
    This audio source will be used for the speaker check.

  2. Enter diagnostic mode (Click here).



  3. E268484
  4. Select "Failure Diagnosis" from the "Service Menu" screen.



  5. E278176
  6. Select "System Check" from the "Failure Diagnosis" screen.



  7. E273721
  8. Select "SPCheck ON" from the "System Check Mode" screen.

  9. Check the speaker wiring and check that the speakers are functioning properly.

    HINT:
    1. Check that each speaker outputs sound from the selected audio source properly.
    2. "SPCheck OFF" is displayed during the speaker check.
    3. Sound can be heard from the speakers around the vehicle in order beginning from a speaker on the front side.

  10. Sound stops when any of the following conditions are met:

    1. The "SPCheck OFF" switch is pressed.

    2. The ignition switch is turned off.

    3. Diagnostic mode is turned off.

    4. The screen is changed to another screen.

    5. Audio mode is turned off.