Home › DRIVE LINE › DRIVE SHAFT › FRONT DRIVE SHAFT

FRONT DRIVE SHAFT > REASSEMBLY

for Preparation Click here



1. INSTALL FRONT DRIVE SHAFT BEARING


    C108281E04
  1. Using SST and a press, install a new front drive shaft bearing.

    SST
    09710-30021   (09710-03141)
    09527-10011  

    NOTICE:
    Bearing should be completely installed.



2. INSTALL FRONT DRIVE SHAFT RH HOLE SNAP RING


    C109617
  1. Using a snap ring expander, install a new front drive shaft RH hole snap ring.



3. INSTALL FRONT DRIVE SHAFT DUST COVER


    C108282E04
  1. Using SST and a press, install a new drive shaft dust cover until the distance from the tip of the center drive shaft to the drive shaft dust cover meets the specification, as shown in the illustration.

    SST
    09726-40010  
    09527-10011  

    Distance (A):
    26.8 to 27.4 mm (1.0551 to 1.0787 in.)



4. INSTALL FRONT DRIVE SHAFT DUST COVER RH (for 2WD)


    C108283E03
  1. Using SST and a press, install a new drive shaft dust cover RH until the distance from the tip of the center drive shaft to the drive shaft dust cover RH meets the specification, as shown in the illustration.

    SST
    09527-10011  

    Distance:
    109.5 mm (4.311 in.)

    NOTICE:
    1. Dust cover should be completely installed.
    2. Be careful not to damage the dust cover.



5. INSTALL FRONT DRIVE SHAFT DUST COVER RH (for 4WD)


    F040215E02
  1. Using SST and a press, install a new drive shaft dust cover RH.

    SST
    09527-10011  

    NOTICE:
    1. Dust cover should be completely installed.
    2. Be careful not to damage the dust cover.



6. INSTALL FRONT DRIVE SHAFT DUST COVER LH


    F041033E06
  1. Using SST and a press, install a new drive shaft dust cover LH.

    SST
    09527-10011  

    NOTICE:
    1. Dust cover should be completely installed.
    2. Be careful not to damage the dust cover.



7. INSTALL FRONT DRIVE SHAFT LH HOLE SNAP RING
  1. Install a new hole snap ring to the inboard joint shaft assembly.



8. INSTALL OUTBOARD JOINT BOOT

HINT:
Before installing the boots, wrap the spline of the drive shaft with vinyl tape to prevent the boots from being damaged.



    C104547E02
  1. Install new parts to the outboard joint shaft assembly in the following order.

    1. Outboard joint boot No. 2 clamp (A)

    2. Outboard joint boot (B)

    3. Outboard joint boot clamp (C)

  1. Pack the outboard joint shaft and boot with grease.
    Drive type
    Grease capacity g (oz.)
    2WD
    35 to 55 g (1.2 to 1.9 oz.)
    4WD
    40 to 60 g (1.4 to 2.1 oz.)



9. INSTALL OUTBOARD JOINT BOOT NO. 2 CLAMP
  1. Hold the outboard joint shaft assembly between aluminium plates in a vise.

    NOTICE:
    Do not overtighten the vise.

  1. Install the outboard joint boot No. 2 clamp onto the boot.

  1. Place SST onto the outboard joint boot No. 2 clamp.

    SST
    09521-24010  



    C108286E03
  1. Tighten the SST so that the outboard joint boot No. 2 clamp is pinched.

    SST
    09521-24010  

    NOTICE:
    Do not overtighten the SST.



    C106165E04
  1. Using SST, measure the clearance of the outboard joint boot No. 2 clamp.

    SST
    09240-00020  

    Clearance:
    0.8 mm (0.031 in.) or less

    NOTICE:
    When the measured value is greater than the specified value, retighten the clamp.



10. INSTALL OUTBOARD JOINT BOOT CLAMP
  1. Install the outboard joint boot clamp perform the same procedures as for the outboard joint boot No. 2 clamp.



11. INSTALL FRONT DRIVE SHAFT DAMPER
  1. Install the drive shaft damper to the drive shaft.

  1. Make sure that the damper is on the shaft groove.



    D027407E02
  1. Set the distance, as specified below.

    Distance:
    221.0 +- 2.0 mm (8.701 +- 0.079 in.)



12. INSTALL FRONT DRIVE SHAFT DAMPER RH CLAMP
  1. Hold the outboard joint shaft assembly between aluminium plates in a vise.

    NOTICE:
    Do not overtighten the vise.

  1. Install the drive shaft damper clamp to the damper.

    NOTICE:
    Be sure to install the clamp in the correct position.

  1. Place SST onto the drive shaft damper clamp.

    SST
    09521-24010  



    D027408E04
  1. Tighten the SST so that the clamp is pinched.

    SST
    09521-24010  

    NOTICE:
    Do not overtighten the SST.



    C086268E06
  1. Using SST, measure the clearance of the drive shaft damper clamp.

    SST
    09240-00020  

    Clearance:
    0.8 mm (0.031 in.) or less

    NOTICE:
    Using SST, measure the clearance of the drive shaft damper clamp.



13. INSTALL INBOARD JOINT ASSEMBLY


    C104548E01
  1. Install new parts to the inboard joint shaft assembly in the following order.

    1. Inboard joint boot clamp (A)

    2. Inboard joint boot (B)

    3. Inboard joint boot No. 2 clamp (C)

  1. Hold the outboard joint shaft assembly between aluminium plates in a vise.

    NOTICE:
    Do not overtighten the vise.

  1. Place the beveled side of the tripod axial spline toward the outboard joint shaft.



    C108291E01
  1. Align the matchmarks.



    C104525
  1. Using a brass bar and hammer, tap in the tripod to the outboard joint shaft.

    NOTICE:
    1. Do not tap the roller.
    2. Be sure to install the tripod in the correct direction.



    C108271
  1. Using a snap ring expander, install a new front inner shaft snap ring.

  1. Pack the inboard joint shaft and boot with grease.
    Drive type
    Grease capacity g (oz.)
    2WD
    95 to 115 g (3.4 to 4.1 oz.)
    4WD
    100 to 130 g (3.9 to 4.6 oz.)



    C108270E01
  1. Align the matchmarks, install the inboard joint assembly to the outboard joint shaft assembly.



14. INSTALL FR AXLE INBOARD JOINT BOOT
  1. Install the inboard joint boot to the inboard joint assembly.



15. INSTALL NO. 2 FRONT AXLE INBOARD JOINT BOOT LH CLAMP
  1. Hold the outboard joint shaft assembly between aluminium plates in a vise.

    NOTICE:
    Do not overtighten the vise.

  1. Install the No. 2 front axle inboard joint boot LH clamp onto the boot.



  1. for Omega Type:

    1. Place SST onto the No. 2 front axle inboard joint boot LH clamp.

      SST
      09521-24010  



    2. C108292E03
    3. Tighten the SST so that the No. 2 front axle inboard joint boot LH clamp is pinched.

      SST
      09521-24010  

      NOTICE:
      Do not overtighten the SST.



    4. C086270E05
    5. Using SST, measure the clearance of the No. 2 front axle inboard joint boot LH clamp.

      SST
      09240-00020  

      Clearance:
      0.8 mm (0.031 in.) or less

      NOTICE:
      When the measured value is greater than the specified value, retighten the clamp.



    C160031E01
  1. for claw engagement type:

    1. Using needle nose pliers, install the No. 2 front axle inboard joint boot clamp as shown in the illustration.



16. INSTALL FRONT AXLE INBOARD JOINT BOOT LH CLAMP
  1. Install the front axle inboard joint boot LH clamp perform the same procedures as for the No. 2 front axle inboard joint boot LH clamp.



17. INSPECT FRONT DRIVE SHAFT ASSEMBLY


    C091598
  1. Check that there is no excessive play in the outboard joint.

  1. Check that the inboard joint slides smoothly in the thrust direction.

  1. Check that there is no excessive play in the radial directions of the inboard joint.



    F045048E04
  1. Check the boots for damage.

    HINT:
    For dimension (A), refer to the following table.

    DRIVE TYPE
    LH mm (in.)
    RH mm (in.)
    2WD
    638.40 +- 5.0 (25.1338 +- 0.20)
    957.00 +- 5.0 (37.6771 +- 0.20)
    4WD
    553.64 +- 5.0 (21.7968 +- 0.20)
    992.24 +- 5.0 (39.0645 +- 0.20)