ENGINE UNIT > DISASSEMBLY |
| 1. REMOVE OIL FILLER CAP SUB-ASSEMBLY |
Remove the oil filler cap sub-assembly and oil filler gasket.
| 2. REMOVE SPARK PLUG |
Remove the spark plugs.
| 3. REMOVE OIL PAN DRAIN PLUG |
![]() |
Remove the oil pan drain plug and oil pan drain plug gasket.
| 4. REMOVE VENTILATION VALVE SUB-ASSEMBLY |
![]() |
Remove the ventilation valve sub-assembly.
| 5. REMOVE CAMSHAFT POSITION SENSOR |
![]() |
Remove the 4 bolts and 4 camshaft position sensors.
| 6. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY |
![]() |
Remove the 4 bolts and 4 camshaft oil control valves.
| 7. REMOVE CRANKSHAFT POSITION SENSOR |
![]() |
Remove the bolt and crankshaft position sensor.
| 8. REMOVE NO. 1 OIL PIPE |
![]() |
Remove the 2 oil pipe unions, gaskets and oil pipe.
Remove the oil control valve filter LH and gaskets.
| 9. REMOVE OIL PIPE |
![]() |
Remove the bolt.
Remove the 2 oil pipe unions and oil pipe.
Remove the oil control valve filter RH and gaskets.
| 10. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY |
![]() |
Remove the cylinder block water drain cocks from the cylinder block.
Remove the cylinder block water drain cock plugs from the water drain cocks.
| 11. REMOVE OIL FILTER ELEMENT |
![]() |
Remove the drain plug.
![]() |
Connect the hose to the pipe.
Insert the pipe with the hose into the oil filter cap.
Make sure that the oil is completely drained and remove the pipe and O-ring.
![]() |
Using SST, remove the oil filter cap sub-assembly.
![]() |
Remove the oil filter element and O-ring from the oil filter cap sub-assembly.
| 12. REMOVE CRANKSHAFT PULLEY |
![]() |
Using SST, loosen the crankshaft pulley bolt.
![]() |
Using SST, remove the crankshaft pulley bolt and crankshaft pulley.
| 13. REMOVE OIL COOLER ASSEMBLY |
![]() |
Remove the bolt, 2 clamps, and 4 clips and disconnect the 2 water by-pass hoses.
![]() |
Remove the union bolt, oil cooler assembly, and O-ring.
| 14. REMOVE NO. 1 OIL COOLER BRACKET |
![]() |
Remove the 3 bolts, 3 nuts, and oil cooler pipe with No. 1 oil cooler bracket.
![]() |
Remove the bolt, 2 nuts, No. 1 oil cooler bracket, and gasket.
Using a "TORX" socket wrench E8, remove the 2 stud bolts.
| 15. REMOVE NO. 1 FRONT ENGINE MOUNTING BRACKET LH |
![]() |
Remove the 6 bolts and No. 1 front engine mounting bracket LH.
Using a "TORX" socket wrench E8, remove the 2 stud bolts.
| 16. REMOVE WATER INLET HOUSING |
![]() |
Remove the 2 nuts, water inlet and thermostat.
Remove the gasket.
Remove the drain cock plug.
Remove the drain cock assembly.
Remove the 2 stud bolts.
Separate the No. 1 water by-pass hose.
![]() |
Remove the 2 bolts, nut, and water inlet housing.
![]() |
Remove the 2 O-rings.
| 17. REMOVE WATER OUTLET |
![]() |
Remove the 2 bolts, 4 nuts and water outlet.
![]() |
Remove the 2 gaskets and O-ring.
| 18. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY (for Bank 1) |
![]() |
Remove the 12 bolts, seal washer, cylinder head cover sub-assembly and cylinder head cover gasket.
![]() |
Remove the 3 gaskets.
| 19. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY (for Bank 2) |
![]() |
Remove the 12 bolts, seal washer, cylinder head cover sub-assembly and cylinder head cover gasket.
![]() |
Remove the 3 gaskets.
| 20. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY |
![]() |
Remove the 16 bolts and 2 nuts.
![]() |
Insert the oil pan seal cutter blade between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan sub-assembly.
Using a "TORX" socket wrench E6, remove the 2 stud bolts.
| 21. REMOVE OIL STRAINER SUB-ASSEMBLY |
![]() |
Remove the bolt, 2 nuts, oil strainer sub-assembly and gasket.
Using a "TORX" socket wrench E6, remove the 2 stud bolts.
| 22. REMOVE OIL PAN SUB-ASSEMBLY |
![]() |
Remove the 16 bolts and 2 nuts.
![]() |
Remove the oil pan sub-assembly by prying between the oil pan sub-assembly and cylinder block sub-assembly with a screwdriver.
![]() |
Remove the 2 O-rings.
Using a "TORX" socket wrench E8, remove the 2 stud bolts.
| 23. REMOVE NO. 1 OIL PAN BAFFLE PLATE |
![]() |
Remove the 7 bolts and No. 1 oil pan baffle plate.
| 24. REMOVE ENGINE REAR OIL SEAL RETAINER |
![]() |
Remove the 6 bolts.
![]() |
Using a screwdriver, pry out the engine rear oil seal retainer.
| 25. REMOVE ENGINE REAR OIL SEAL |
![]() |
Place the oil seal retainer on wooden blocks.
Using a screwdriver and a hammer, tap out the oil seal.
| 26. REMOVE WATER PUMP ASSEMBLY |
![]() |
Remove the 16 bolts, water pump assembly and gasket.
| 27. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY |
![]() |
Remove the 15 bolts and 2 nuts as shown in the illustration.
![]() |
Remove the timing chain cover sub-assembly by prying between the timing chain cover and cylinder head sub-assembly or cylinder block sub-assembly with a screwdriver.
Remove the 4 bolts, chain cover plate and chain cover plate gasket.
![]() |
Remove the gasket.
| 28. REMOVE TIMING CHAIN CASE OIL SEAL |
![]() |
Using a screwdriver, pry out the timing chain case oil seal.
| 29. SET NO. 1 CYLINDER TO TDC / COMPRESSION |
Temporarily tighten the pulley set bolt.
![]() |
Set the timing mark on the crank angle sensor plate to the RH block bore center line (TDC / compression).
![]() |
Check that the timing marks of the camshaft timing gears are aligned with those of the bearing cap as shown in the illustration.
If not, turn the crankshaft 1 revolution (360°) and align the timing marks as above.
| 30. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY |
![]() |
Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.
Move the stopper plate downward to set the lock, and insert a pin of φ1.27 mm (0.05 in.) into the stopper plate's hole.
![]() |
Remove the 2 bolts and No. 1 chain tensioner assembly.
| 31. REMOVE CHAIN TENSIONER SLIPPER |
Remove the chain tensioner slipper.
| 32. REMOVE CHAIN SUB-ASSEMBLY |
![]() |
Turn the crankshaft counterclockwise 10° to loosen the chain sub-assembly of the crankshaft timing sprocket.
Remove the pulley set bolt.
![]() |
Remove the chain sub-assembly from the crankshaft timing sprocket and place it on the crankshaft.
![]() |
Turn the camshaft timing gear assembly on the bank 1 clockwise (approximately 60°) and set it as shown in the illustration. Be sure to loosen the chain between the banks.
Remove the chain.
| 33. REMOVE IDLE SPROCKET ASSEMBLY |
![]() |
Using a 10 mm hexagon wrench, remove the No. 2 idle gear shaft, idle sprocket assembly and No. 1 idle gear shaft.
| 34. REMOVE NO. 1 CHAIN VIBRATION DAMPER |
![]() |
Remove the 2 bolts and No. 1 chain vibration damper.
| 35. REMOVE NO. 2 CHAIN VIBRATION DAMPER |
Remove the 2 No. 2 chain vibration dampers.
| 36. REMOVE CRANKSHAFT TIMING SPROCKET |
![]() |
Remove the crankshaft timing sprocket from the crankshaft.
Remove the 2 keys from the crankshaft.
| 37. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1) |
![]() |
While raising the No. 2 chain tensioner assembly, insert a pin of φ1.0 mm (0.039 in.) into the hole to fix the No. 2 chain tensioner.
![]() |
Using SST to hold the hexagonal portion of each camshaft, loosen the bolts of the camshaft timing gear assembly and the camshaft timing exhaust gear assembly RH.
Remove the 2 bolts, the camshaft timing gear assembly and the camshaft timing exhaust gear assembly RH together with the No. 2 chain.
| 38. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY |
![]() |
Remove the bolt and No. 2 chain tensioner assembly.
| 39. REMOVE CAMSHAFT BEARING CAP (for Bank 1) |
![]() |
Check that the camshafts are positioned as shown in the illustration.
![]() |
Uniformly loosen and remove the 8 bearing cap bolts in the sequence shown in the illustration.
![]() |
Uniformly loosen and remove the 12 bearing cap bolts in the sequence shown in the illustration.
Remove the 5 bearing caps.
| 40. REMOVE CAMSHAFT |
Remove the camshaft.
| 41. REMOVE NO. 2 CAMSHAFT |
Remove the No. 2 camshaft.
| 42. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH |
![]() |
Remove the camshaft housing sub-assembly RH by prying between the cylinder head and camshaft housing sub-assembly RH with a screwdriver.
| 43. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2) |
![]() |
While pushing down the No. 3 chain tensioner assembly, insert a pin of φ1.0 mm (0.039 in.) into the hole to fix the No. 3 chain tensioner assembly.
![]() |
Using SST to hold the hexagonal portion of each camshaft, loosen the bolts of the camshaft timing gear assembly and the camshaft timing exhaust gear assembly LH.
Remove the 2 bolts, the camshaft timing gear assembly and the camshaft timing exhaust gear assembly LH together with the No. 2 chain.
| 44. REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY |
![]() |
Remove the bolt and No. 3 chain tensioner assembly.
| 45. REMOVE CAMSHAFT BEARING CAP (for Bank 2) |
![]() |
Check that the camshafts are positioned as shown in the illustration.
![]() |
Uniformly loosen and remove the 8 bearing cap bolts in the sequence shown in the illustration.
![]() |
Uniformly loosen and remove the 13 bearing cap bolts in the sequence shown in the illustration.
Remove the 5 bearing caps.
| 46. REMOVE NO. 3 CAMSHAFT |
Remove the No. 3 camshaft.
| 47. REMOVE NO. 4 CAMSHAFT |
Remove the No. 4 camshaft.
| 48. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH |
![]() |
Remove the camshaft housing sub-assembly LH by prying between the cylinder head and camshaft housing sub-assembly LH with a screwdriver.
| 49. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY |
Remove the 24 No. 1 valve rocker arm sub-assemblies.
| 50. REMOVE VALVE LASH ADJUSTER ASSEMBLY |
Remove the 24 valve lash adjuster assemblies from the cylinder head.
| 51. REMOVE CYLINDER HEAD SUB-ASSEMBLY RH |
![]() |
Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 bolts in the sequence shown in the illustration. Remove the 8 cylinder head bolts and plate washers.
Remove the cylinder head sub-assembly RH and cylinder head gasket.
| 52. REMOVE CYLINDER HEAD SUB-ASSEMBLY LH |
![]() |
Uniformly loosen and remove the cylinder head set bolts in the sequence shown in the illustration.
![]() |
Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 bolts in the sequence shown in the illustration. Remove the 8 cylinder head bolts and plate washers.
Remove the cylinder head sub-assembly LH and No. 2 cylinder head gasket.
| 53. REMOVE WATER INLET PIPE |
Remove 2 clamps and separate the No. 1 water by-pass hose.
![]() |
Remove the 2 bolts and water inlet pipe.
| 54. REMOVE VALVE STEM CAP |
Remove the valve stem caps from the cylinder heads.
| 55. REMOVE INTAKE VALVE |
![]() |
Using SST, compress the inner compression spring and remove the valve spring retainer locks.
Remove the valve spring retainer, inner compression spring and intake valve.
| 56. REMOVE EXHAUST VALVE |
![]() |
Using SST, compress the inner compression spring and remove the valve spring retainer locks.
Remove the valve spring retainer, inner compression spring and exhaust valve.
| 57. REMOVE VALVE STEM OIL SEAL |
![]() |
Using needle-nose pliers, remove the valve stem oil seals.
| 58. REMOVE VALVE SPRING SEAT |
![]() |
Using compressed air and a magnetic finger, remove the valve spring seats by blowing air onto them.
| 59. REMOVE NO. 1 STRAIGHT SCREW PLUG |
![]() |
Using a 10 mm hexagon wrench, remove the 4 No. 1 straight screw plugs and 4 gaskets.
| 60. REMOVE NO. 2 STRAIGHT SCREW PLUG |
![]() |
Using a 14 mm hexagon wrench, remove the 2 No. 2 straight screw plugs and 2 gaskets.
| 61. REMOVE RING PIN |
| 62. REMOVE STUD BOLT |
| 63. REMOVE STRAIGHT PIN |
| 64. REMOVE INTAKE VALVE GUIDE BUSH |
Heat the cylinder head to 80 to 100°C (176 to 212°F).
Place the cylinder head on wooden blocks.
![]() |
Using SST and a hammer, tap out the intake valve guide bushes.
| 65. REMOVE EXHAUST VALVE GUIDE BUSH |
Heat the cylinder head to 80 to 100°C (176 to 212°F).
Place the cylinder head on wooden blocks.
![]() |
Using SST and a hammer, tap out the exhaust valve guide bushes.
| 66. REMOVE PISTON SUB-ASSEMBLY WITH CONNECTING ROD |
Check that the matchmarks on the connecting rod sub-assembly and connecting rod cap are aligned.
![]() |
Remove the 2 connecting rod cap bolts.
![]() |
Using the 2 removed connecting rod cap bolts, remove the connecting rod cap and lower bearing by wiggling the connecting rod cap right and left.
![]() |
Using a ridge reamer, remove all the carbon from the top of the cylinder.
Push the piston, connecting rod assembly and upper bearing through the top of the cylinder block.
| 67. REMOVE CONNECTING ROD BEARING |
| 68. REMOVE CRANKSHAFT |
![]() |
Uniformly loosen and remove the 8 crankshaft bearing cap bolts and seal washers in several steps and in the sequence shown in the illustration.
![]() |
Uniformly loosen the 16 crankshaft bearing cap bolts, in several steps and in the sequence shown in the illustration.
![]() |
Using a screwdriver, pry out the main bearing caps. Remove the 4 crankshaft bearing caps and lower crankshaft bearings.
Remove the crankshaft.
| 69. REMOVE CRANKSHAFT BEARING |
Remove the upper crankshaft bearing and lower crankshaft bearing.
| 70. REMOVE CRANKSHAFT THRUST WASHER SET |
![]() |
Remove the upper crankshaft bearings and upper crankshaft thrust washers from the cylinder block sub-assembly.
| 71. REMOVE PISTON RING SET |
![]() |
Using a piston ring expander, remove the 2 compression rings.
Remove the oil ring expander and 2 side rails by hand.
| 72. REMOVE PISTON SUB-ASSEMBLY WITH PIN |
![]() |
Check the fitting condition between the piston and piston pin.
Try to move the piston back and forth on the piston pin.
If any movement is felt, replace the piston and pin as a set.
![]() |
Disconnect the connecting rod from the piston.
Using a screwdriver, pry off the piston pin hole snap rings from the piston.
![]() |
Gradually heat the piston to approximately 80°C (176°F).
![]() |
Using a brass bar and plastic hammer, lightly tap out the piston pin and remove the connecting rod.
![]() |
Using a gasket scraper, remove the carbon from the piston top.
![]() |
Using a groove cleaning tool or broken ring, clean the piston ring grooves.
![]() |
Using solvent and a brush, thoroughly clean the piston.
| 73. REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY |
![]() |
Using a 5 mm hexagon wrench, remove the bolts and No. 1 oil nozzle sub-assembly.
Check the 3 oil nozzles for damage or clogging.
If necessary, replace the No. 1 oil nozzle sub-assembly.
| 74. CLEAN CYLINDER BLOCK |