Home › CRUISE CONTROL SYSTEM › CRUISE CONTROL › DYNAMIC LASER CRUISE CONTROL SYSTEM

DYNAMIC LASER CRUISE CONTROL SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK DISTANCE CONTROL ECU

I034896E08


Terminal No. (Symbols)
Wiring Color
Terminal Description
Condition
Specified Condition
D2-1 (B) - D2-12 (GND)
B-R - BR
Battery
Always
10 to 14 V
D2-8 (CANH) - D2-12 (GND)
B - BR
CAN communication signal
CAN communication circuit
Pulse generation
D2-9 (CANL) - D2-12 (GND)
W - BR
CAN communication signal
CAN communication circuit
Pulse generation
D2-10 (SGND) - Body ground
BR - Body ground
Ground
Always
Below 1 Ω
D2-12 (GND) - Body ground
BR - Body ground
Ground
Always
Below 1 Ω
D2-13 (IGB) - D2-12 (GND)
W-L - BR
Ignition switch ON signal
Ignition switch off
Below 1 V
D2-13 (IGB) - D2-12 (GND)
W-L - BR
Ignition switch ON signal
Ignition switch ON
10 to 14 V
D2-22 (LRDD) - D2-10 (SGND)
G - BR
Laser sensor input signal
Ignition switch ON
Pulse generation
(see waveform 1)
D2-23 (LRRD) - D2-10 (SGND)
Y - BR
Laser sensor output signal
Ignition switch ON
Pulse generation
(see waveform 2)
D2-16 (MODE) - D2-12 (GND)
W - BR
Steering pad switch signal (Distance control switch signal)
Ignition switch ON, Steering pad switch signal on
0 to 2 V
D2-16 (MODE) - D2-12 (GND)
W - BR
Steering pad switch signal (Distance control switch signal)
Ignition switch ON, Steering pad switch signal off
10 to 14 V


    E109730E04
  1. Reference: waveform 1

    HINT:
    1. Terminal: LRDD - SGND
    2. Gauge set: 2 V/DIV., 10 ms./DIV.
    3. Condition: ignition switch in the ON position



  2. E109731E04
  3. Reference: waveform 2

    HINT:
    1. Terminal: LRRD - SGND
    2. Gauge set: 2 V/DIV., 5 ms./DIV.
    3. Condition: ignition switch in the ON position


CHECK ECM
If the value is not within the specified range, the ECM may have a malfunction.

E127018E06


Terminal No. (Symbols)
Wiring Color
Terminal Description
Condition
Specified Condition
E4-15 (STP) - E11-1 (E1)
G-W - BR
Stop light signal
Brake pedal released (Stop light switch off)
Below 1.5 V
E4-15 (STP) - E11-1 (E1)
G-W - BR
Stop light signal
Brake pedal depressed (Stop light switch on)
7.5 to 14 V
E4-16 (ST1-) - E11-1 (E1)
LG-R - BR
Stop light signal
Ignition switch ON, Brake pedal depressed (Stop light switch on)
Below 1.5 V
E4-16 (ST1-) - E11-1 (E1)
LG-R - BR
Stop light signal
Ignition switch ON, Brake pedal released (Stop light switch off)
7.5 to 14 V
E4-23 (TC) - E11-1 (E1)
P-B - BR
Terminal TC of DLC3
Ignition switch ON
10 to 14 V
E4-23 (TC) - E11-1 (E1)
P-B - BR
Terminal TC of DLC3
Connect terminals TC and CG of DLC3
Below 1 V
E4-31 (LGND) - Body ground
R - Body ground
Ground
Always
Below 1 Ω
E5-2 (CCS) - E11-1 (E1)
B - BR
Cruise control main switch signal
Ignition switch ON
10 to 14 V
E5-2 (CCS) - E11-1 (E1)
B - BR
Cruise control main switch signal
CANCEL switch on
6.6 to 10.1 V
E5-2 (CCS) - E11-1 (E1)
B - BR
Cruise control main switch signal
- (COAST)/SET switch on
4.5 to 7.1 V
E5-2 (CCS) - E11-1 (E1)
B - BR
Cruise control main switch signal
+ (ACCEL)/RES (RESUME) switch on
2.3 to 4.0 V
E5-2 (CCS) - E11-1 (E1)
B - BR
Cruise control main switch signal
Main switch on
Below 1 V
E5-4 (CCHG) - E11-1 (E1)
P - BR
Distance control switch signal
Ignition switch ON, Cruise control main switch on, MODE switch on
Below 1 V
E5-4 (CCHG) - E11-1 (E1)
P - BR
Distance control switch signal
Ignition switch ON, Cruise control main switch on, MODE switch off
10 to 14 V
E11-1 (E1) - Body ground
BR - Body ground
Ground
Always
Below 1 Ω

CHECK LASER SENSOR

I039263E06


Terminal No. (Symbols)
Wiring Color
Terminal Description
Condition
Specified Condition
L1-1 (LGND) - Body ground
R - Body ground
Ground (Distance signal)
Always
Below 1 Ω
L1-2 (SGND) - Body ground
BR - Body ground
Ground
Always
Below 1 Ω
L1-3 (LRDD) - L1-2 (SGND)
G - BR
Laser sensor output signal
Ignition switch ON
Pulse generation
(see waveform 1)
L1-4 (LRRD) - L1-2 (SGND)
Y - BR
Laser sensor input signal
Ignition switch ON
Pulse generation
(see waveform 2)
L1-5 (IGB) - L1-2 (SGND)
W-L - BR
Power source
Ignition switch ON
10 to 14 V


    E109730E04
  1. Reference: waveform 1

    HINT:
    1. Terminal: LRDD - SGND
    2. Gauge set: 2 V/DIV., 10 ms./DIV.
    3. Condition: ignition switch in the ON position



  2. E109731E04
  3. Reference: waveform 2

    HINT:
    1. Terminal: LRRD - SGND
    2. Gauge set: 2 V/DIV., 5 ms./DIV.
    3. Condition: ignition switch in the ON position


BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

F045080E12


Terminal No. (Symbols)
Wiring Color
Terminal Description
Condition
Specified Condition
S3-30 (BZ) - S3-32 (GND1)
G-O - W-B
Skid control buzzer circuit
Ignition switch ON
Skid control buzzer is sounded
Below 1.0 V ←→ 10 to 14 V
Ignition switch ON
Skid control buzzer is not sounded
10 to 14 V
S3-16 (STPO) - S3-32 (GND1)
W-R - W-B
Stop light control relay output signal
Ignition switch ON
10 to 14 V
S3-21 (STP2) - S3-32 (GND1)
G-Y - W-B
Stop light control relay input signal
Brake pedal released
(Stop light switch off)
Below 1.0 V
Brake pedal depressed
(Stop light switch on)
10 to 14 V
S3-27 (STP1) - S3-32 (GND1)
G-W - W-B
Stop light switch input signal
Ignition switch off → ON
Below 1.0 V → 10 to 14 V
Ignition switch off
Brake pedal depressed (Stop light switch on)
10 to 14 V