Home › BODY ELECTRICAL › METER › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > Tachometer Malfunction

for Preparation Click here


DESCRIPTION

The meter CPU receives the engine revolution signal from the ECM via the direct lines. The meter CPU displays engine revolution data that is calculated based on the data received from the ECM.

WIRING DIAGRAM


E118061E11


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Connect Techstream to the DLC3.

  1. Turn the switch to the ON position.

  1. Turn the tester ON.

  1. Enter the following menus: Body Electrical / Main Body / Active Test.

  1. Check the operation by referring to the values in the table below.

    Combination Meter: 
    Tester Display
    Test Part
    Test Details
    Diagnostic Note
    Tacho Meter Operation
    Tachometer
    0, 1,000, 2,000, 3,000, 4,000, 5,000, 6,000, 7,000 (rpm)
    -

    OK:
    Needle indication is normal.



NG
REPLACE COMBINATION METER ASSEMBLY
OK


2.READ VALUE USING TECHSTREAM (ENGINE SPEED SIGNAL)
  1. Connect Techstream to the DLC3.

  1. Turn the switch to the ON position.

  1. Turn the tester ON.

  1. Enter the following menus: Body Electrical / Combination Meter / Data List.

  1. Check the values by referring to the values in the table below.

    Combination Meter: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Engine Rpm
    Engine speed/Min.: 0 rpm, Max.: 12,750 rpm
    Almost same as actual engine speed (When engine is running)
    -

    OK:
    Engine speed displayed on the tester is almost the same as the actual engine speed.



NG
Go to step 3
OK

REPLACE COMBINATION METER ASSEMBLY 

3.READ VALUE USING TECHSTREAM (ENGINE SPEED SIGNAL)
  1. Connect Techstream to the DLC3.

  1. Turn the switch to the ON position.

  1. Turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List.

  1. Check the values by referring to the values in the table below.

    Engine and ECT: 
    Item
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Engine Speed
    Engine speed/Min.: 0 rpm, Max.: 12,750 rpm
    Almost same as actual engine speed (When engine is running)
    -



NG
GO TO SFI SYSTEM
OK


4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)


    E159310E01
  1. Disconnect the E5 and C10 connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E5-1 (TACH) - C10-37 (S)
    Always
    Below 1 Ω
    E5-1 (TACH) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT ECM (INPUT WAVEFORM)


    E118053E11
  1. Check the input signal waveform.

    1. Reconnect the E5 connector.

    2. Connect the oscilloscope to terminal C10-37 (S) and body ground.

    3. Start the engine.



    4. E107976E02
    5. Check the signal waveform according to the condition(s) in the table below.
      Item
      Condition
      Tool setting
      5 V/DIV., 10 ms./DIV.
      Vehicle condition
      Engine idle speed

      OK:
      The waveform is displayed as shown in the illustration.



OK
REPLACE COMBINATION METER ASSEMBLY
NG

REPLACE ECM