AUTOMATIC TRANSAXLE SYSTEM > ROAD TEST |
| PROBLEM SYMPTOM CONFIRMATION |
Based on the result of the customer problem analysis, try to reproduce the symptoms. If the problem is that the transaxle does not shift up, shift down, or the shift point is too high or too low, conduct the following road test referring to the automatic shift schedule and simulate the problem symptoms.
| ROAD TEST |
D position test:
Shift into the D position and fully depress the accelerator pedal and check the following points.
Check up-shift operation.
Check that 1 → 2, 2 → 3, 3 → 4 and 4 → 5th up-shifts take place, and that the shift points conform to the automatic shift schedule (Click here).
Check for shift shock and slip.
Check for shock and slip at the 1 → 2, 2 → 3, 3 → 4 and 4 → 5th up-shifts.
Check for abnormal noise and vibration.
Drive in the D position lock-up or 5th gear, and check for abnormal noises and vibration.
Check kick-down operation.
Check that the possible kick-down vehicle speed limits for 2nd to 1st, 3rd to 2nd, 4th to 3rd, 5th to 4th kick-downs conform to those indicated on the automatic shift schedule while driving through all gears with the shift lever in the D position (Click here).
Check abnormal shock and slip at kick-down.
Check the lock-up mechanism.
4 (O/D OFF) position test:
Shift into the 4 position and fully depress the accelerator pedal and check the following points.
Check up-shift operation.
Check that the 1 → 2, 2 → 3 and 3 → 4 up-shift take place and that the shift point conforms to the automatic shift schedule (Click here).
Check engine braking.
While driving in the 4 position and 4th gear, release the accelerator pedal and check the engine braking effect.
Check for abnormal noise during acceleration and deceleration, and for shock at up-shift and down-shift.
3 position test:
Shift into the 3 position and fully depress the accelerator pedal and check the following points.
Check up-shift operation.
Check that the 1 → 2 and 2 → 3 up-shift take place and that the shift point conforms to the automatic shift schedule (Click here).
Check engine braking.
While running in the 3 position and 3rd gear, release the accelerator pedal and check the engine braking effect.
Check for abnormal noise during acceleration and deceleration, and for shock at up-shift and down-shift.
2 position test:
Shift into the 2 position and fully depress the accelerator pedal and check the following points.
Check up-shift operation.
Check that the 1 →2 up-shift takes place and that the shift point conforms to the automatic shift schedule (Click here).
Check engine braking.
While running in the 2 position and 2nd gear, release the accelerator pedal and check the engine braking effect.
Check for abnormal noise during acceleration and deceleration, and for shock at up-shift and down-shift.
L position test:
Shift into the L position and fully depress the accelerator pedal and check the following points.
Check no up-shift.
While running in the L position, check that there is no up-shift to 2nd gear.
Check engine braking.
While running in the L position, release the accelerator pedal and check the engine braking effect.
Check for abnormal noise during acceleration and deceleration.
R position test:
Shift into the R position and fully depress the accelerator pedal and check for slipping.
P position test:
Stop the vehicle on the grade (more than 5°) and after shifting into the P position, release the parking brake. Then, check that the parking lock pawl holds the vehicle in place.
Uphill/downhill control function test:
Check that the gear does not up-shift to the 4th or 5th gear while the vehicle is driving uphill.
Check that the gear automatically down-shifts from 5th to 4th or from the 4th to 3rd gear when brake is applied while the vehicle is driving downhill.