DTC P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0705 | (A) Any 2 or more signals of the following are ON simultaneously (2-trip detection logic)
(D) Both 1 and 2 conditions are met (2-trip detection logic)
|
|
| Related DTCs | P0705: Park/neutral position switch/Verify switch input |
| Required sensors/Components | Park/neutral position switch |
| Frequency of operation | Continuous |
| Duration | Condition (A), (B), (D) 2 sec. Condition (C) 60 sec. |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever this DTC is not present. | None |
| Ignition switch | ON |
| Battery voltage | 10.5 V or more |
| One of the following conditions are met: Condition (A), (B), (C) and (D) |
| Number of the following signal input at the same time | 2 or more |
| P switch | ON |
| N switch | ON |
| R switch | ON |
| D switch | ON |
| 3 switch | ON |
| 2 switch | ON |
| Number of the following signal input at the same time | 2 or more |
| NSW (STAR) switch | ON |
| R switch | ON |
| D switch | ON |
| 3 switch | ON |
| 2 switch | ON |
| NSW (STAR) switch | OFF |
| P switch | OFF |
| N switch | OFF |
| R switch | OFF |
| D switch | OFF |
| 3 switch | OFF |
| 2 switch | OFF |
| (1) One of the following conditions are met | - |
| NSW (STAR) switch | ON |
| P switch | ON |
| R switch | ON |
| N switch | ON |
| (2) One of the following conditions are met | - |
| 4 shift position switch | ON |
| L shift position switch | ON |
| Park/neutral Position switch | The park/neutral position switch sends only one signal to the ECM. |

| 1.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
![]() |
Disconnect the park/neutral position switch connector.
Measure resistance according to the value(s) in the table below when the shift lever is moved to each position.
| Shift Position | Tester Connection | Specified Condition |
| P | 2 - 6 and 4 - 5 | Below 1 Ω |
| Except P | 10 kΩ or higher | |
| R | 2 - 1 | Below 1 Ω |
| Except R | 10 kΩ or higher | |
| N | 2 - 9 and 4 - 5 | Below 1 Ω |
| Except N | 10 kΩ or higher | |
| D and 4 | 2 - 7 | Below 1 Ω |
| Except D and 4 | 10 kΩ or higher | |
| 3 | 2 - 3 | Below 1 Ω |
| Except 3 | 10 kΩ or higher | |
| 2 and L | 2 - 8 | Below 1 Ω |
| Except 2 and L | 10 kΩ or higher |
|
| ||||
| OK | |
| 2.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY |
![]() |
Connect the park/neutral position switch connector.
Disconnect the transmission control switch connector of shift lock control unit assembly.
Measure resistance according to the value(s) in the table below when the shift lever is moved to each position.
| Shift Position | Tester Connection | Specified Condition |
| D | 2 - 9 | Below 1 Ω |
| 4 | ↑ | 10 kΩ or higher |
| D | 3 - 9 | 10 kΩ or higher |
| 4 | ↑ | Below 1 Ω |
| 2 | 5 - 10 | Below 1 Ω |
| L | ↑ | 10 kΩ or higher |
| 2 | 4 - 10 | 10 kΩ or higher |
| L | ↑ | Below 1 Ω |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM) |
![]() |
Connect the transmission control switch connector of shift lock control unit assembly.
Turn the ignition switch to the ON position, and measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.
| Shift Position | Tester Connection | Specified Condition |
| P and N | E10-8 (NSW (STAR)) - Body ground | Below 1 V |
| Except P and N | 11 to 14 V | |
| P | E5-23 (P) - Body ground | 11 to 14 V |
| Except P | Below 1 V | |
| N | E5-22 (N) - Body ground | 11 to 14 V |
| Except N | Below 1 V | |
| R | E5-11 (R) - Body ground | 11 to 14 V*
|
| Except R | Below 1 V | |
| D and 4 | E5-21 (D) - Body ground | 11 to 14 V |
| Except D and 4 | Below 1 V | |
| 4 | E5-20 (4) - Body ground | 11 to 14 V |
| Except 4 | Below 1 V | |
| 3 | E5-19 (3) - Body ground | 11 to 14 V |
| Except 3 | Below 1 V | |
| 2 and L | E5-10 (2) - Body ground | 11 to 14 V |
| Except 2 and L | Below 1 V | |
| L | E5-9 (L) - Body ground | 11 to 14 V |
| Except L | Below 1 V |
|
| ||||
| OK | ||
| ||