CAN COMMUNICATION SYSTEM > Open in CAN Main Bus Line |
| Symptom | Trouble Area |
| Resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 69 Ω or higher. |
|

| 1.CHECK DLC3 |
Turn the ignition switch off.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D1-6 (CANH) - D1-14 (CANL) | Ignition switch off | 108 to 132 Ω |
| Result | Proceed to |
| 108 to 132 Ω | A |
| 132 Ω or higher | B |
|
| ||||
| A | |
| 2.CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM CAN MAIN BUS WIRE) |
Turn the ignition switch off.
![]() |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E5-33 (CANH) - E5-34 (CANL) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | ||
| ||
| 3.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NETWORK GATEWAY ECU CAN MAIN BUS WIRE) |
Reconnect the ECM connector.
Disconnect the network gateway ECU connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G4-17 (CA1H) - G4-18 (CA1L) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | ||
| ||
| 4.CHECK FOR OPEN IN CAN BUS MAIN WIRE (JUNCTION CONNECTOR - NETWORK GATEWAY ECU) |
Reconnect the network gateway ECU connector.
Disconnect the junction connector (J17).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J17-6 (CANH) - J17-17 (CANL) | Ignition switch off | 108 to 132 Ω |
| Result | Proceed to |
| OK (without VSC) | A |
| OK (with VSC) | B |
| NG | C |
|
| ||||
|
| ||||
| A | |
| 5.CHECK CHECK FOR OPEN IN CANBUS MAIN WIRE (JUNCTION CONNECTOR - ECM) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J17-7 (CANH) - J17-18 (CANL) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | ||
| ||
| 6.CHECK FOR OPEN IN CAN BUS MAIN WIRE (JUNCTION CONNECTOR - CAN JUNCTION CONNECTOR) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J17-7 (CANH) - J17-18 (CANL) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | ||
| ||
| 7.CHECK FOR OPEN IN CAN BUS MAIN WIRE (CAN JUNCTION CONNECTOR - JUNCTION CONNECTOR) |
Reconnect the junction connector (J17).
Disconnect the CAN junction connector (J49).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J49-3 (CANH) - J49-7 (CANL) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | |
| 8.CHECK FOR OPEN IN CAN BUS MAIN WIRE (CAN JUNCTION CONNECTOR - ECM) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J49-4 (CANH) - J49-6 (CANL) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | ||
| ||