Home › ENGINE › 2GR-FE ENGINE CONTROL SYSTEM › KNOCK SENSOR

KNOCK SENSOR > INSTALLATION

for Preparation Click here



1. INSTALL KNOCK CONTROL SENSOR


    A132951E01
  1. Install the 2 knock control sensors with the 2 bolts as shown in the illustration.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the 2 knock control sensor connectors.



2. INSTALL INTAKE MANIFOLD

NOTICE:
DO NOT apply oil to the bolts listed below:
Tightening Parts
Intake Manifold and Cylinder Head Sub-assembly RH
Intake Manifold and Cylinder Head Sub-assembly LH



    A134933
  1. Set a new gasket on each cylinder head.

    NOTICE:
    1. Align the port holes of the gasket and cylinder head.
    2. Make sure that the gasket is installed in the correct direction.

  1. Set the intake manifold on the cylinder heads.

  1. Install and tighten the 6 bolts and 4 nuts uniformly in several steps.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



3. INSTALL FUEL MAIN TUBE SUB-ASSEMBLY


    B012944
  1. Push in the fuel tube connector to the fuel pipe until the fuel tube makes a "click" sound.

    NOTICE:
    1. Check for damage or contamination on the connected part of the pipe.
    2. Check if the pipe and the connector are securely connected by trying to pull them apart.



    A155045
  1. Install the No. 1 fuel pipe clamp.



4. INSTALL INTAKE AIR SURGE TANK

NOTICE:
DO NOT apply oil to the bolts listed below.
Oil Application Prohibited Bolt
Bolt for surge tank and intake manifold
Bolt for No. 1 surge tank stay and surge tank
Bolt for throttle body bracket and surge tank



    A129468E09
  1. Install a new gasket to the intake air surge tank [A].

  1. Using a 5 mm hexagon socket wrench, install the 4 bolts [B].

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Install the intake air surge tank with the 2 nuts and 2 bolts [C].

    Torque:
    Nut:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }
    Bolt:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



    A129467
  1. Connect the connector [D].



    A138457E05
  1. Connect the union to check valve hose [E].

  1. Connect the ventilation hose No. 2 [F].



    A129464E08
  1. Install the clamp and connect the throttle with motor body assembly connector [G].

  1. Connect the vapor feed hose [H].

  1. Connect the 2 water by-pass hoses to the throttle with motor body assembly [I].



5. INSTALL AIR CLEANER CASE SUB-ASSEMBLY


    A155039
  1. Install the air cleaner case with the 3 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the vacuum hose.

  1. Connect the vacuum switching valve connector.



6. INSTALL AIR CLEANER CAP SUB-ASSEMBLY


    A135114
  1. Install the air cleaner cap sub-assembly with the 2 bolts.



    A135113E01
  1. Connect the the vacuum hose (EVAP) to the air cleaner hose.

  1. Install the No. 2 ventilation hose and air cleaner hose band.



    A135112E01
  1. Connect the 3 vacuum hoses.



7. ADD ENGINE COOLANT
  1. Tighten the radiator drain cock plug by hand.

  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for cylinder block drain cock plugs

  1. Remove the air drain cock plug from the water inlet housing.



    A162799E01
  1. Loosen the air drain plug at the top of the radiator 3 or 4 turns.

  1. Add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the engine air drain cock hole. Then install the air drain cock plug to the water inlet housing.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for air drain cock plug

  1. Continue to add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the radiator air drain hole. Then close the air drain plug at the top of the radiator.

    HINT:
    If the coolant level at the radiator inlet opening drops after squeezing the No. 1 and No. 2 radiator hoses, add coolant.

  1. Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).

    Standard capacity:
    11.3 liters (12.0 US qts, 10.0 Imp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    2. Contact your TOYOTA dealer for further details.

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Slowly pour coolant into the radiator reservoir tank until it reaches the FULL line.

  1. Squeeze the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level is low, add coolant.

  1. Bleed air from the cooling system.

    1. Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.

      HINT:
      The thermostat open timing can be confirmed by squeezing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.

    2. Maintain the engine speed at 2500 to 3000 rpm.

    3. Squeeze the inlet and outlet radiator hoses several times by hand to bleed air.

      CAUTION:
      When squeezing the radiator hoses:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the radiator fan.

      NOTICE:
      1. Make sure that the radiator reservoir still has some coolant in it.
      2. If the coolant temperature gauge indicates an excessive temperature, turn off the engine and let it cool.
      3. If there is not enough coolant, the engine may overheat or be seriously damaged.
      4. If the radiator reservoir does not have enough coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the FULL line.

  1. Stop the engine and wait until the engine coolant cools down.

  1. Add engine coolant to the FULL line on the radiator reservoir.



8. INSPECT FOR ENGINE COOLANT LEAK

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

NOTICE:
Before performing each inspection, turn the A/C switch OFF.



    A161453
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.



9. INSPECT FOR FUEL LEAK
  1. Check fuel pump operation.

    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch to ON.

      NOTICE:
      Do not start the engine.

    3. Turn the Techstream main switch on.

    4. Select the following menu items: Power train / Engine and ECT / Active Test / Control the Fuel Pump Speed.

    5. Check for pressure in the fuel inlet tube from the fuel line. Check that sound of fuel flowing in the fuel tank can be heard. If no sound can be heard, check the integration relay, fuel pump, ECM and wiring connector.

  1. Inspect for fuel leaks (*1).

    1. Check that there are no fuel leaks anywhere on the system after performing maintenance. If there is a fuel leak, repair or replace parts as necessary.

  1. Turn the ignition switch off.

  1. Disconnect the Techstream from the DLC3.



10. INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY


    A162367
  1. Install the front outer cowl top panel sub-assembly with the 7 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



    A162368
  1. Install the 2 clips.

  1. Install the fuel pump resistor with the nut.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



11. INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

HINT:
(Click here)



12. INSTALL V-BANK COVER SUB-ASSEMBLY


    A162365
  1. Fit the 3 retainers and install the V-bank cover.