Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) > Air Conditioning Compressor Magnetic Clutch Circuit

for Preparation Click here


DESCRIPTION

When the A/C amplifier is turned on, a magnetic clutch ON signal is sent from the MGC terminal of the A/C amplifier. Then, the MG CLT relay turns on to operate the magnetic clutch.

WIRING DIAGRAM


E124490E11


INSPECTION PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
  1. Use Techstream to check if the CAN communication system is functioning normally.

    Result:
    Result
    Proceed to
    CAN DTC is not output
    A
    CAN DTC is output
    B



B
GO TO CAN COMMUNICATION SYSTEM
A


2.CHECK MULTIPLEX COMMUNICATION SYSTEM
  1. Use Techstream to check if the multiplex communication system is functioning normally.

    Result:
    Result
    Proceed to
    MPX DTC is not output
    A
    MPX DTC is output
    B



B
GO TO MULTIPLEX COMMUNICATION SYSTEM
A


3.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Connect Techstream to the DLC3.

  1. Turn the ignition switch to the ON position and turn Techstream on.

  1. Select the item below in the Active Test and then check that the relay operates.

    Active Test / Air Conditioner: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Magnetic Clutch Relay
    Magnetic clutch relay
    OFF, ON
    -

    OK:
    Magnetic clutch relay operates.



NG
Go to step 4
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE 

4.INSPECT FUSE (HTR)
  1. Remove the HTR fuse from the driver side junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Item
    Condition
    Specified Condition
    HTR fuse
    Always
    Below 1 Ω

  1. Reconnect the HTR fuse to the driver side junction block.



NG
REPLACE FUSE (HTR)
OK


5.INSPECT RELAY (MG CLT)


    B060778E04
  1. Remove the MG CLT relay from the No. 3 relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 5
    10 kΩ or higher
    3 - 5
    Below 1 Ω
    (when battery voltage is applied to terminals 1 and 2)

  1. Install the MG CLT relay to the No. 3 relay block.



NG
REPLACE RELAY (MG CLT)
OK


6.CHECK HARNESS AND CONNECTOR (A/C AMPLIFIER - BATTERY)


    E143742E44
  1. Disconnect the connector from the A/C amplifier.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A9-5 (MGC) - Body ground
    Ignition switch: OFF
    Below 1 V
    A9-5 (MGC) - Body ground
    Ignition switch: ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.INSPECT A/C AMPLIFIER


    E147476E02
  1. Reconnect the connector to the A/C amplifier.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A9-5 (MGC) - Body ground
    Ignition switch: ON
    A/C switch: OFF
    11 to 14 V
    A9-5 (MGC) - Body ground
    Ignition switch: ON
    A/C switch: ON
    Below 1 V



NG
REPLACE A/C AMPLIFIER
OK


8.INSPECT COMPRESSOR AND MAGNETIC CLUTCH


    E145186E06
  1. Disconnect the connector from the compressor and magnetic clutch.



    E124482E04
  1. Disconnect the connector from the magnetic clutch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A31-3 (MG+) - A-1
    Always
    Below 1 Ω
    A31-3 (MG+) - Body ground
    Always
    10 kΩ or higher



NG
REPLACE COMPRESSOR AND MAGNETIC CLUTCH
OK


9.INSPECT MAGNETIC CLUTCH


    E147609E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A-1 - Body ground
    Always
    3.4 to 3.8 Ω

  1. When connector terminal A1 is connected to the positive (+) battery terminal, check that the following occurs: 1) the magnetic clutch's operating sound can be heard, and 2) the magnetic clutch's hub and rotor lock.



NG
REPLACE MAGNETIC CLUTCH
OK


10.CHECK HARNESS AND CONNECTOR (NO. 3 RELAY BLOCK - BATTERY)


    E147378E01
  1. Remove the MG CLT relay from the No. 3 relay block.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified Condition
    Relay block MG CLT relay terminal 5 - Body ground
    11 to 14 V
    Relay block MG CLT relay terminal 1 - Body ground
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 3 RELAY BLOCK - COMPRESSOR AND MAGNETIC CLUTCH)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR