Home › BRAKE › BRAKE CONTROL › ANTI-LOCK BRAKE SYSTEM

DTC    C1241/41    Low Battery Positive Voltage

for Preparation Click here


DESCRIPTION

If there is a problem with the brake actuator assembly (skid control ECU) power supply circuit, the skid control ECU outputs the DTC and prohibits the ABS operation with the fail safe function.
If the voltage supplied to the IG1 terminal is not within the DTC detection threshold due to malfunctions in such as the battery and alternator circuit, this DTC is stored.

DTC No.
DTC Detection Condition
Trouble Area
C1241/41
When any of the following is detected:
  1. Vehicle speed is 3 km/h (1.8 mph) or more and IG1 terminal voltage is 9.5 V or less for at least 10 seconds.
  2. While the solenoid relay is ON, the IG1 terminal voltage is 10 V or less and the relay contact is open solenoid fault detecting conditions are established.
  3. Voltage of ECU terminal IG1 remains at more than 17 V for 1 second or more..
  1. Battery
  2. ECU-IG fuse
  3. Charging system
  4. Power source circuit

WIRING DIAGRAM


F045116E05


INSPECTION PROCEDURE

1.INSPECT BATTERY
  1. Check the battery voltage.

    Standard voltage:
    11 to 14 V



NG
INSPECT CHARGING SYSTEM
OK


2.INSPECT FUSE (ECU-IG FUSE)
F045093E04
  1. Remove the ECU-IG fuse from the driver side J/B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    ECU-IG (10 A) fuse
    Below 1 Ω (Continuity)



NG
REPLACE FUSE (ECU-IG FUSE)
OK


3.READ VALUE USING TECHSTREAM (IG1 POWER SUPPLY)
  1. Install the ECU-IG fuse.

  1. Connect Techstream to the DLC3.

  1. Turn the ignition switch to the ON position and turn the Techstream main switch on.

  1. Start the engine.

  1. Select the Data List mode on Techstream.

    ABS / VSC / TRAC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ECU IG Power Voltage
    ECU IG power supply voltage / TOO LOW, NORMAL, TOO HIGH
    TOO LOW: Less than 9.5 V
    NORMAL: 9.5 to 14 V
    TOO HIGH: More than 14 V
    -

  1. Measure the voltage output from the ECU displayed on Techstream.

    OK:
    "Normal" is displayed.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)
OK


4.INSPECT SKID CONTROL ECU (IG1 TERMINAL VOLTAGE)


    C058919E24
  1. Disconnect the skid control ECU connector.

  1. Turn the ignition switch to ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified Condition
    S3-3 (IG1) - Body ground
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)
OK


5.INSPECT SKID CONTROL ECU (GND TERMINAL CONTINUITY)


    C058919E22
  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    S3-1 (GND1) - Body ground
    Below 1 Ω
    S3-23 (GND2) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)
OK


6.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Check that the same DTC is recorded (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.


    Result:

    Condition
    Proceed to
    DTC (C1241/41) is output
    A
    DTC (C1241/41) is not output (When troubleshooting in accordance with the DTC CHART)
    B
    DTC (C1241/41) is not output (When troubleshooting in accordance with the PROBLEM SYMPTOMS TABLE)
    C



B
END

C
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
A

REPLACE BRAKE ACTUATOR ASSEMBLY