Home › SUSPENSION & AXLE › TIRE AND WHEEL › TIRE PRESSURE WARNING SYSTEM

TIRE PRESSURE WARNING SYSTEM > INITIALIZATION

for Preparation Click here



DESCRIPTION OF INITIALIZATION
  1. Perform initialization in the following cases:

    1. Before delivery of a new vehicle.
    2. After replacement of the tire pressure warning ECU*.
    3. After replacement of the tire pressure warning valve and transmitter*.

    HINT:
    *: Perform initialization after the transmitter ID registration is completed (Click here).

  2. Before initialization

    1. Set the air pressure of all tires to the specified value (Click here).

      NOTICE:
      Make sure the tires are cooled down.


INITIALIZATION PROCEDURE
  1. Turn the ignition switch ON.



  2. C159182E02
  3. Press and hold the tire pressure warning reset switch for 3 seconds or more so that the tire pressure warning light blinks 3 times.

  4. Turn the ignition switch OFF.

  5. Connect Techstream to the DLC3.

  6. Turn the ignition switch ON and the tester ON.

  7. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.



  8. H102392E79
  9. Confirm that the tire pressure data of all tires are displayed on the tester screen in order to check the completion.

    NOTICE:
    1. The initialization is normally completed within 5 to 6 minutes.
    2. If the initialization has not been completed successfully, DTC C2177/77 is set after the vehicle is driven for 20 minutes or more.
    3. The initialization can be terminated by connecting terminals 13 (TC) and 4 (CG) of the DLC3.

      Tire Pressure Monitor 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      ID1 Tire Inflation Pressure
      ID1 tire inflation pressure /
      min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / -100 kPa (-1 kgf/cm2, -14 psi)
      max.: Absolute pressure / 637.5 kPa (6.5 kgf/cm2, 92 psi), Relative pressure / 537.5 kPa (5.4 kgf/cm2, 78 psi)
      Actual tire inflation pressure
      If 0 kPa (0 kgf/cm2, 0 psi) is displayed for absolute pressure or -100 kPa (-1 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.*
      ID2 Tire Inflation Pressure
      ID2 tire inflation pressure /
      min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / -100 kPa (-1 kgf/cm2, -14 psi)
      max.: Absolute pressure / 637.5 kPa (6.5 kgf/cm2, 92 psi), Relative pressure / 537.5 kPa (5.4 kgf/cm2, 78 psi)
      Actual tire inflation pressure
      If 0 kPa (0 kgf/cm2, 0 psi) is displayed for absolute pressure or -100 kPa (-1 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.*
      ID3 Tire Inflation Pressure
      ID3 tire inflation pressure /
      min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / -100 kPa (-1 kgf/cm2, -14 psi)
      max.: Absolute pressure / 637.5 kPa (6.5 kgf/cm2, 92 psi), Relative pressure / 537.5 kPa (5.4 kgf/cm2, 78 psi)
      Actual tire inflation pressure
      If 0 kPa (0 kgf/cm2, 0 psi) is displayed for absolute pressure or -100 kPa (-1 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.*
      ID4 Tire Inflation Pressure
      ID4 tire inflation pressure /
      min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / -100 kPa (-1 kgf/cm2, -14 psi)
      max.: Absolute pressure / 637.5 kPa (6.5 kgf/cm2, 92 psi), Relative pressure / 537.5 kPa (5.4 kgf/cm2, 78 psi)
      Actual tire inflation pressure
      If 0 kPa (0 kgf/cm2, 0 psi) is displayed for absolute pressure or -100 kPa (-1 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.*

      HINT:
      1. The initialization is complete when the DATA LIST "ID Tire Inflation Pressure" display shows the correct pressures.
      2. *: It may take up to about 5 to 6 minutes to update the tire pressure data. If the values are not displayed after about 5 to 6 minutes, perform troubleshooting according to the inspection procedure for DTCs C2121/21 to C2124/24 (Click here).