Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

DTC    B1437/37    Rear Air Mix Damper Position Sensor Circuit

for Preparation Click here


DESCRIPTION

E109300E26
This sensor detects the position of the rear air mix control servo motor (water valve servo motor) and sends the appropriate signals to the A/C amplifier. The position sensor is built in the rear air mix control servo motor (water valve servo motor).
The position sensor's resistance changes as the rear air mix control servo motor valve moves.
It outputs voltage (5 V) that is input to terminal 2 and terminal 3 via the variable resistor, and then to the A/C amplifier.
The A/C amplifier determines the valve position based on the input voltage from the position sensor.

DTC No.
DTC Detection Condition
Trouble Area
B1437/37
Open or short in power source circuit in rear air mix damper position sensor circuit.
  1. Rear air mix control servo motor (water valve servo motor)
  2. Harness and connector between rear air mix control servo motor (water valve servo motor) and A/C amplifier
  3. A/C amplifier

WIRING DIAGRAM


I036321E25


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM
  1. Connect Techstream to the DLC3.

  1. Turn the ignition switch to the ON position and turn Techstream on.

  1. Select the items below in the Data List, and read the display on Techstream.

    Data List / Air Conditioner: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Air Mix Damper (Rear)
    Air mix damper position (Rear) / min.: -14%, max.: 113.5%
    Damper is at "MAX. COOL": 0%
    Damper is at "MAX. HOT": 86.5%
    -
    Air Mix Damper Targ (Rear)
    Air mix damper target position (Rear) / min.: -14%, max.: 113.5%

    OK:
    The display is as specified in the normal condition column.


    Result:

    Result
    Proceed to
    NG
    A
    OK (When troubleshooting according to the PROBLEM SYMPTOMS TABLE)
    B
    OK (When troubleshooting according to the DTC)
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C
REPLACE A/C AMPLIFIER
A


2.INSPECT REAR AIR MIX CONTROL SERVO MOTOR (WATER VALVE SERVO MOTOR)


    E145191E01
  1. Remove the rear air mix control servo motor (water valve servo motor).

  1. Disconnect the connector from the rear air mix control servo motor (water valve servo motor).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    W2-1 - W2-2
    Always
    4.2 to 7.8 kΩ

  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    1. In order to turn the motor to the "MAX. COOL" position, connect the positive (+) lead to terminal 5, and the negative (-) lead to terminal 4.
    2. In order to turn the motor to the "MAX. HOT" position, connect the positive (+) lead to terminal 4, and the negative (-) lead to terminal 5.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    W2-3 - W2-1
    MAX. COOL position
    3.4 to 6.2 kΩ
    W2-3 - W2-1
    MAX. HOT position
    1.2 to 2.2 kΩ



    E108925E10
  1. As the rear air mix control servo motor (water valve servo motor) moves from the cool side to the hot side, the resistance decreases gradually without interruption.



NG
REPLACE REAR AIR MIX CONTROL SERVO MOTOR (WATER VALVE SERVO MOTOR)
OK


3.CHECK HARNESS AND CONNECTOR (REAR AIR MIX CONTROL SERVO MOTOR - A/C AMPLIFIER)


    E145121E07
  1. Disconnect the connector from the A/C amplifier.



    E141047E09
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A10-21 (TPH) - W2-3
    Always
    Below 1 Ω
    A10-12 (S5) - W2-2
    Always
    Below 1 Ω
    A10-13 (SG) - W2-1
    Always
    Below 1 Ω
    A10-21 (TPH) - Body ground
    Always
    10 kΩ or higher
    A10-12 (S5) - Body ground
    Always
    10 kΩ or higher
    A10-13 (SG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE A/C AMPLIFIER