Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

DTC    B1432/32    Air Inlet Damper Position Sensor Circuit

for Preparation Click here


DESCRIPTION

E109300E25
This sensor detects the position of the air inlet control servo motor and sends the appropriate signals to the A/C amplifier. The position sensor is built in the air inlet control servo motor.
The position sensor's resistance changes as the air inlet control servo motor arm moves.
It outputs voltage (5 V) that is input to terminal 1 and terminal 3 via the variable resistor, and then to the A/C amplifier.
The A/C amplifier determines the arm position based on the input voltage from the position sensor.

DTC No.
DTC Detection Condition
Trouble Area
B1432/32
Open or short in power source circuit in air inlet damper position sensor circuit
  1. Air inlet control servo motor (air inlet damper position sensor)
  2. Harness or connector between air inlet control servo motor (air inlet damper position sensor) and A/C amplifier
  3. A/C amplifier

WIRING DIAGRAM


I036321E22


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM
  1. Connect Techstream to the DLC3.

  1. Turn the ignition switch to the ON position and turn Techstream on.

  1. Select the items below in the Data List, and read the display on Techstream.

    Data List / Air Conditioner: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Air Inlet Damper Position
    Air inlet damper position / min.: -14%, max.: 113.5%
    Damper is at "RECIRCULATION": -10%
    Damper is at "FRESH": 110%
    Damper is at "HALF-RECIRCULATION": 35 to 75%
    Open in the circuit: 50.0%
    Air Inlet Damper Target
    Air inlet damper target position / min.: -14%, max.: 113.5%

    OK:
    The display is as specified in the normal condition column.


    Result:

    Result
    Proceed to
    NG
    A
    OK (When troubleshooting according to the PROBLEM SYMPTOMS TABLE)
    B
    OK (When troubleshooting according to the DTC)
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C
REPLACE A/C AMPLIFIER
A


2.INSPECT AIR INLET CONTROL SERVO MOTOR


    E145188E01
  1. Remove the air inlet control servo motor.

  1. Disconnect the connector from the air inlet control servo motor.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A16-1 - A16-2
    Always
    4.2 to 7.8 kΩ

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A16-3 - A16-2
    RECIRCULATION position
    3.6 to 6.7 kΩ
    A16-3 - A16-2
    FRESH position
    0.6 to 1.1 kΩ



    E108925E09
  1. As the air inlet control servo motor moves from RECIRCULATION to FRESH, the resistance decreases gradually without interruption.



NG
REPLACE AIR INLET CONTROL SERVO MOTOR
OK


3.CHECK HARNESS AND CONNECTOR (AIR INLET CONTROL SERVO MOTOR - A/C AMPLIFIER)


    E145121E04
  1. Disconnect the connector from the A/C amplifier.



    E143742E36
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A9-28 (TPI) - A16-3
    Always
    Below 1 Ω
    A9-21 (SG-1) - A16-2
    Always
    Below 1 Ω
    A9-30 (S5-1) - A16-1
    Always
    Below 1 Ω
    A9-28 (TPI) - Body ground
    Always
    10 kΩ or higher
    A9-21 (SG-1) - Body ground
    Always
    10 kΩ or higher
    A9-30 (S5-1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE A/C AMPLIFIER