Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

DTC    B1436/36    Air Mix Damper Position Sensor Circuit (Driver Side)

for Preparation Click here


DESCRIPTION

E109300E01
This sensor detects the position of the air mix control servo motor (air outlet damper) and sends the appropriate signals to the A/C amplifier. The position sensor is built in the air mix control servo motor. The position sensor resistance changes as the air mix control servo motor arm moves.
It outputs voltage (5 V) that is input to terminal 1 and terminal 3 via the variable resistor, and then to the A/C amplifier. The A/C amplifier determines the arm position based on the input voltage from the position sensor.

DTC No.
DTC Detection Condition
Trouble Area
B1436/36
Open or short in power source circuit in air mix damper position sensor circuit.
  1. Air mix control servo motor (air mix damper position sensor)
  2. Harness or connector between air mix control servo motor and A/C amplifier
  3. A/C amplifier

WIRING DIAGRAM


I036321E24


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM
  1. Connect Techstream to the DLC3.

  1. Turn the ignition switch to the ON position and turn Techstream on.

  1. Select the items below in the Data List, and read the display on Techstream.

    Data List / Air Conditioner: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Air Mix Damper Position (D)
    Air mix damper position (Driver side) / min.: -14%, max.: 113.5%
    Damper is at "MAX. COOL": -5%
    Damper is at "MAX. HOT": 105%
    -
    Air Mix Damper Target (D)
    Air mix damper target position (Driver side) / min.: -14%, max.: 113.5%

    OK:
    The display is as specified in the normal condition column.


    Result:

    Result
    Proceed to
    NG
    A
    OK (When troubleshooting according to the PROBLEM SYMPTOM TABLE)
    B
    OK (When troubleshooting according to the DTC)
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C
REPLACE A/C AMPLIFIER
A


2.INSPECT AIR MIX CONTROL SERVO MOTOR


    E109269E09
  1. Remove the air mix control servo motor.

  1. Disconnect the connector from the air mix control servo motor.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A17-1 - A17-2
    Always
    4.2 to 7.8 kΩ

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A17-3 - A17-2
    MAX. COOL position
    3.4 to 6.2 kΩ
    A17-3 - A17-2
    MAX. HOT position
    0.8 to 1.6 kΩ



    E108925E08
  1. As the air mix control servo motor moves from the COOL side to the HOT side, the resistance decreases gradually without interruption.



NG
REPLACE AIR MIX CONTROL SERVO MOTOR
OK


3.CHECK HARNESS AND CONNECTOR (AIR MIX CONTROL SERVO MOTOR - A/C AMPLIFIER)


    E145121E06
  1. Disconnect the connector from the A/C amplifier.



    E143742E38
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A9-26 (TPD) - A17-3
    Always
    Below 1 Ω
    A9-21 (SG-1) - A17-2
    Always
    Below 1 Ω
    A9-30 (S5-1) - A17-1
    Always
    Below 1 Ω
    A9-26 (TPD) - Body ground
    Always
    10 kΩ or higher
    A9-21 (SG-1) - Body ground
    Always
    10 kΩ or higher
    A9-30 (S5-1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE A/C AMPLIFIER