Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

DTC    B1442/42    Air Inlet Damper Control Servo Motor Circuit

for Preparation Click here


DESCRIPTION

The air inlet control servo motor is controlled by the A/C amplifier and moved to the desired position.
The air inlet control servo motor switches the air inlet mode by rotating (normal, reverse) with electrical power from the A/C amplifier. This controls intake air and changes the mode between "RECIRCULATION", "FRESH", and "HALF-RECIRCULATION".

DTC No.
DTC Detection Condition
Trouble Area
B1442/42
Air inlet damper position sensor value does not change even if A/C amplifier operates air inlet control servo motor.
  1. Air inlet control servo motor
  2. Harness or connector between air inlet control servo motor and A/C amplifier
  3. A/C amplifier

WIRING DIAGRAM


I036322E21


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM
  1. Connect Techstream to the DLC3.

  1. Turn the ignition switch to the ON position and turn Techstream on.

  1. Select the items below in the Data List, and read the display on Techstream.

    Data List / Air Conditioner: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Air Inlet Damper Position
    Air inlet damper position / min.: -14%, max.: 113.5%
    Damper is at "RECIRCULATION": -10%
    Damper is at "HALF-RECIRCULATION": 35 to 75%
    Damper is at "FRESH": 110%
    Open in the circuit: 50.0%
    Air Inlet Damper Target
    Air inlet damper target position / min.: -14%, max.: 113.5%

    OK:
    When the target position is "RECIRCULATION" (-10%), the actual opening angle is 19.0% or less.
    When the target position is "FRESH" (110%), the actual opening angle is 81.0% or more.


    Result:

    Result
    Proceed to
    NG
    A
    OK (When troubleshooting according to the PROBLEM SYMPTOMS TABLE)
    B
    OK (When troubleshooting according to the DTC)
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C
REPLACE A/C AMPLIFIER
A


2.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Remove the glove box to see and check the recirculation damper operation.

  1. Connect Techstream to the DLC3.

  1. Turn the ignition switch to the ON position and turn Techstream on.

  1. Select the item below in the Active Test and then check that the damper operates.

    Active Test / Air Conditioner: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Air Inlet Damper Position (Linear)
    Air inlet damper position (linear)
    min.: -14%, max.: 113.5%
    -

    OK:
    Lever turns from "RECIRCULATION" side to "FRESH" side smoothly.
    Lever turns from "FRESH" side to "RECIRCULATION" side smoothly.


    Result:

    Result
    Proceed to
    NG
    A
    OK (When troubleshooting according to the PROBLEM SYMPTOMS TABLE)
    B
    OK (When troubleshooting according to the DTC)
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C
REPLACE A/C AMPLIFIER
A


3.PERFORM ACTUATOR CHECK
  1. Remove the glove box to see and check the recirculation damper operation.

  1. Enter the actuator check mode (Click here).

  1. Press the DEF switch and check the operation of the recirculation damper.

    Display Code
    Recirculation Damper Position
    0
    FRESH (110%)
    1
    FRESH (110%)
    2
    FRESH (110%)
    3
    R/F (50%)
    4
    RECIRCULATION (-10%)
    5
    RECIRCULATION (-10%)
    6
    RECIRCULATION (-10%)
    7
    RECIRCULATION (-10%)
    8
    RECIRCULATION (-10%)
    9
    RECIRCULATION (-10%)

    OK:
    Recirculation damper position changes in accordance with each display code.


    Result:

    Result
    Proceed to
    NG
    A
    OK (When troubleshooting according to the PROBLEM SYMPTOMS TABLE)
    B
    OK (When troubleshooting according to the DTC)
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C
REPLACE A/C AMPLIFIER
A


4.INSPECT AIR INLET CONTROL SERVO MOTOR


    E145188E02
  1. Remove the air inlet control servo motor.

  1. Disconnect the connector from the air inlet control servo motor.

  1. Connect the positive (+) lead from the battery to terminal 5 and the negative (-) lead to terminal 4, then check that the lever turns to the "FRESH" position smoothly.

    OK:
    Lever turns to "FRESH" position smoothly.

  1. Connect the positive (+) lead from the battery to terminal 4 and the negative (-) lead to terminal 5, then check that the lever turns to the "RECIRCULATION" position smoothly.

    OK:
    Lever turns to "RECIRCULATION" position smoothly.



NG
REPLACE AIR INLET CONTROL SERVO MOTOR
OK


5.CHECK HARNESS AND CONNECTOR (AIR INLET CONTROL SERVO MOTOR - A/C AMPLIFIER)


    E145121E10
  1. Disconnect the connector from the A/C amplifier.



    E143742E40
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A9-17 (AIR) - A16-4
    Always
    Below 1 Ω
    A9-16 (AIF) - A16-5
    Always
    Below 1 Ω
    A9-17 (AIR) - Body ground
    Always
    10 kΩ or higher
    A9-16 (AIF) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE A/C AMPLIFIER