DTC B1449/49 Rear Air Outlet Damper Control Servo Motor Circuit |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1449/49 | Rear air outlet damper position sensor value does not change even if A/C amplifier operates rear air outlet control servo motor. |
|

| 1.READ VALUE USING TECHSTREAM |
Connect Techstream to the DLC3.
Turn the ignition switch to the ON position and turn Techstream on.
Select the items below in the Data List, and read the display on Techstream.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Air Outlet Damper (Rear) | Air outlet mode damper position (Rear) / min.: -14%, max.: 113.5% | Damper is at "FACE1": 0% Damper is at "FACE2": 16.5% Damper is at "FACE/FOOT": 44% Damper is at "FOOT": 100% | Open in the circuit: 50.0% |
| Air Outlet Damper Targ (Rear) | Air outlet mode damper target position (Rear) / min.: -14%, max.: 113.5% |
| Result | Proceed to |
| NG | A |
| OK (When troubleshooting according to the PROBLEM SYMPTOMS TABLE) | B |
| OK (When troubleshooting according to the DTC) | C |
|
| ||||
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM |
Connect Techstream to the DLC3.
Turn the ignition switch to the ON position and turn Techstream on.
Select the item below in the Active Test and then check the air flow position by hand.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Air Outlet Damper Position (Rear) | Air outlet damper position (Rear) | min.: -14%, max.: 113.5% | - |
| Result | Proceed to |
| NG | A |
| OK (When troubleshooting according to the PROBLEM SYMPTOMS TABLE) | B |
| OK (When troubleshooting according to the DTC) | C |
|
| ||||
|
| ||||
| A | |
| 3.PERFORM ACTUATOR CHECK |
Warm up the engine.
Enter the actuator check mode (Click here).
Press the DEF switch and change to step operation.
Press the DEF switch and check the air flow by hand.
| Display Code | Air flow condition |
| 0 | FACE1 (0%) |
| 1 | FACE1 (0%) |
| 2 | FACE1 (0%) |
| 3 | FACE2 (16.5%) |
| 4 | FACE/FOOT (44%) |
| 5 | FACE/FOOT (44%) |
| 6 | FACE/FOOT (44%) |
| 7 | FOOT (100%) |
| 8 | FOOT (100%) |
| 9 | FOOT (100%) |
| Result | Proceed to |
| NG | A |
| OK (When troubleshooting according to the PROBLEM SYMPTOMS TABLE) | B |
| OK (When troubleshooting according to the DTC) | C |
|
| ||||
|
| ||||
| A | |
| 4.INSPECT REAR AIR OUTLET CONTROL SERVO MOTOR |
![]() |
Remove the rear air outlet control servo motor.
Disconnect the connector from the rear air outlet control servo motor.
Connect the positive (+) lead from the battery to terminal 4 and the negative (-) lead to terminal 5, then check that the lever turns to the "FOOT" position smoothly.
Connect the positive (+) lead from the battery to terminal 5 and the negative (-) lead to terminal 4, then check that the lever turn to the "FACE" position smoothly.
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (REAR AIR OUTLET CONTROL SERVO MOTOR - A/C AMPLIFIER) |
![]() |
Disconnect the connector from the A/C amplifier.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A10-2 (FACE) - A30-5 | Always | Below 1 Ω |
| A10-1 (FOOT) - A30-4 | Always | Below 1 Ω |
| A10-2 (FACE) - Body ground | Always | 10 kΩ or higher |
| A10-1 (FOOT) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||