DTC B1446/46 Air Mix Damper Control Servo Motor Circuit (Driver Side) |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1446/46 | Air mix damper position sensor value does not change even if A/C amplifier operates air mix control servo motor. |
|

| 1.READ VALUE USING TECHSTREAM |
Connect Techstream to the DLC3.
Turn the ignition switch to the ON position and turn Techstream on.
Select the items below in the Data List, and read the display on Techstream.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Air Mix Damper Position (D) | Air mix damper position (Driver side) / min.: -14%, max.: 113.5% | Damper is at "MAX. COOL": -5% Damper is at "MAX. HOT": 105% | - |
| Air Mix Damper Target (D) | Air mix damper target position (Driver side) / min.: -14%, max.: 113.5% |
| Result | Proceed to |
| NG | A |
| OK (When troubleshooting according to the PROBLEM SYMPTOM TABLE) | B |
| OK (When troubleshooting according to the DTC) | C |
|
| ||||
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM |
Connect Techstream to the DLC3.
Turn the ignition switch to the ON position and turn Techstream on.
Select the item below in the Active Test and then check the air flow temperature by hand.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Air Mix Damper (D Side) | Air mix damper (Driver side) | min.: -14%, max.: 113.5% | - |
| Result | Proceed to |
| NG | A |
| OK (When troubleshooting according to the PROBLEM SYMPTOM TABLE) | B |
| OK (When troubleshooting according to the DTC) | C |
|
| ||||
|
| ||||
| A | |
| 3.PERFORM ACTUATOR CHECK |
Enter the actuator check mode (Click here).
Press the DEF switch and change to the step operation.
Check the air flow temperature by hand.
| Display Code | Air Mix Damper Operation |
| 0 | "COOL" side (-5%) |
| 1 | "COOL" side (-5%) |
| 2 | "COOL" side (-5%) |
| 3 | "COOL" side (-5%) |
| 4 | "COOL"/"HOT" (50% opened) |
| 5 | "COOL"/"HOT" (50% opened) |
| 6 | "HOT" side (105%) |
| 7 | "HOT" side (105%) |
| 8 | "HOT" side (105%) |
| 9 | "HOT" side (105%) |
| Result | Proceed to |
| NG | A |
| OK (When troubleshooting according to the PROBLEM SYMPTOM TABLE) | B |
| OK (When troubleshooting according to the DTC) | C |
|
| ||||
|
| ||||
| A | |
| 4.INSPECT AIR MIX CONTROL SERVO MOTOR |
![]() |
Remove the air mix control servo motor.
Disconnect the connector from the air mix control servo motor.
Connect the positive (+) lead from the battery to terminal 5 and the negative (-) lead to terminal 4, then check that the lever turns to the "MAX. HOT" position smoothly.
Connect the positive (+) lead from the battery to terminal 4 and the negative (-) lead to terminal 5, then check that the lever turns to the "MAX. COOL" position smoothly.
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (AIR MIX CONTROL SERVO MOTOR - A/C AMPLIFIER) |
![]() |
Disconnect the connector from the A/C amplifier.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A9-13 (AMDC) - A17-4 | Always | Below 1 Ω |
| A9-12 (AMDH) - A17-5 | Always | Below 1 Ω |
| A9-13 (AMDC) - Body ground | Always | 10 kΩ or higher |
| A9-12 (AMDH) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||