Home › BRAKE › BRAKE CONTROL › ANTI-LOCK BRAKE SYSTEM

DTC    C0273/13    Open in ABS Motor Relay Circuit

DTC    C0274/14    Short to B+ in ABS Motor Relay Circuit

for Preparation Click here


DESCRIPTION

The ABS motor relay supplies power to the ABS pump motor. While the ABS is activated, the ECU turns the motor relay on and operates the ABS pump motor.
If the voltage supplied to the motor relay (+BM) is below the DTCs detection threshold due to low voltage from the battery/alternator, the DTCs may be stored.

DTC No.
DTC Detection Condition
Trouble Area
C0273/13
With the IG1 terminal voltage 10 V or less during initial check or ABS control, pump motor relay is turned ON and relay contact is not ON for 0.2 seconds or more.
  1. ABS 1 fuse
  2. ABS motor relay
  3. ABS motor relay circuit
  4. Brake actuator assembly
C0274/14
The motor contact is ON for 3 seconds or more when the motor relay is OFF.
  1. ABS 1 fuse
  2. ABS motor relay
  3. ABS motor relay circuit
  4. Brake actuator assembly

WIRING DIAGRAM


C119436E01


INSPECTION PROCEDURE

1.INSPECT FUSE (ABS 1 FUSE)
  1. Remove the ABS 1 fuse from the FL block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    ABS 1 (50 A) fuse
    Below 1 Ω (Continuity)



NG
REPLACE FUSE (ABS 1 FUSE)
OK


2.INSPECT SKID CONTROL ECU (+BM TERMINAL VOLTAGE)


    C113872E02
  1. Install the ABS 1 fuse.

  1. Disconnect the skid control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    S3-24 (+BM) - Body ground
    Always
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (+BM CIRCUIT)
OK


3.INSPECT SKID CONTROL ECU (GND TERMINAL CONTINUITY)


    C058919E22
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    S3-1 (GND1) - Body ground
    Below 1 Ω
    S3-23 (GND2) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)
OK


4.PERFORM ACTIVE TEST USING TECHSTREAM (ABS MOTOR RELAY)
  1. Reconnect the skid control ECU connector.

  1. Connect Techstream to the DLC3.

  1. Turn the ignition switch to the ON position and turn the Techstream main switch on.

  1. Start the engine.

  1. Select the Active Test mode on Techstream.

    ABS / VSC / TRAC: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    ABS Motor Relay
    ABS motor relay
    Relay ON / OFF
    Operating sound of motor is heard

  1. Check operating sound of the ABS motor when operating it with Techstream.

    OK:
    The operating sound of the ABS motor is heard.



NG
REPLACE BRAKE ACTUATOR ASSEMBLY
OK


5.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle at the speed of 6 km/h (4 mph) or more.

  1. Check that the same DTCs are recorded (Click here).

    HINT:
    1. Reinstall the sensors, connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.
    2. If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU, with the ignition switch on and the stop light switch off, the ECU performs self-diagnosis of the motor and solenoid circuits.


    Result:

    Condition
    Proceed to
    DTCs (C0273/13 and C0274/14) are output
    A
    DTCs (C0273/13 and C0274/14) are not output
    B

    HINT:
    1. If any DTCs are output while jiggling a connector or wire harness of the brake actuator (skid control ECU), inspect and repair the connector or wire harness.
    2. If the normal system code is output, slightly jiggle the connectors, wire harnesses, and fuses of the brake actuator assembly. Make sure that no DTCs are output.
    3. These DTCs may be stored due to a malfunction in the connector terminal connection, etc.



B
END
A

REPLACE BRAKE ACTUATOR ASSEMBLY