Home › TRANSMISSION · U151E AUTOMATIC TRANSAXLE › SHIFT LOCK SYSTEM

SHIFT LOCK SYSTEM > ON-VEHICLE INSPECTION

for Preparation Click here



1. CHECK SHIFT LOCK OPERATION
  1. Move the shift lever to the P position.

  1. Turn the ignition switch to the LOCK position.

  1. Check that the shift lever cannot be moved to any position other than P.

  1. Turn the ignition switch to the on position, depress the brake pedal and check that the shift lever can be moved to another position. If operation can not be done as specified, inspect the shift lock control unit.



2. CHECK SHIFT LOCK RELEASE BUTTON OPERATION
  1. Using a small screwdriver, remove the shift lock release cover.

  1. When operating the shift lever with the shift lock release button pressed, check that the lever can be moved to any position other than P.
    If operation can not be done as specified, check the shift lever assembly installation condition.



3. CHECK KEY INTERLOCK OPERATION
  1. Turn the ignition switch to the ON position.

  1. Depress the brake pedal and move the shift lever to any position other than P.

  1. Check that the ignition key cannot be turned to the LOCK position.

  1. Move the shift lever to the P position, turn the ignition key to the LOCK position and check that the ignition key can be removed.
    If operation cannot be done as specified, inspect the shift lock control unit.



4. INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY


    C098999E11
  1. Measure the voltage according to the value(s) in the table below.

    HINT:
    Do not disconnect the shift lock control unit assembly connector.


    Voltage:

    Terminal
    Measuring Condition
    Voltage (V)
    6 (ACC) - 8 (E)
    Ignition switch ACC
    10 to 14
    6 (ACC) - 8 (E)
    Ignition switch OFF
    Below 1
    7 (STP) - 8 (E)
    Depress brake pedal
    10 to 14
    7 (STP) - 8 (E)
    Release brake pedal
    Below 1
    12 (KLS+) - 8 (E)
    1. 1. Ignition switch ACC and shift lever P position
    2. 2. Ignition switch ACC and shift lever except P position
    3. 3. Ignition switch ACC and shift lever except P position (After approx. 1 second)
    1. Below 1
    2. 7.5 to 11
    3. 6 to 9
    1 (IG) - 8 (E)
    Ignition switch ON
    10 to 14
    1 (IG) - 8 (E)
    Ignition switch OFF
    Below 1



    C098999E12
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    Do not disconnect the shift lock control unit assembly connector.

    If operation cannot be done as specified, replace the shift lever assembly.

    Resistance:

    Terminal
    Measuring Condition
    Specified Value
    8 (E) - Body ground
    Always
    Below 1 Ω



5. INSPECT KEY INTER LOCK SOLENOID


    D025589E02
  1. Disconnect the solenoid connector.

  1. Connect KLS+ (4) terminal to the batteries' positive (+) terminal and KLS (3) terminal to the battery negative (-) terminal, and apply about 12 V between KLS+ - KLS- terminals.

  1. Check that operation noise can be heard from the solenoid.
    If the solenoid does not operate, replace the solenoid.



6. INSPECT SHIFT LOCK SOLENOID


    D030503E01
  1. Disconnect the solenoid connector.

  1. Connect SSL+ (2) terminal to the batteries' positive (+) terminal, and SLS- (1) terminal to the battery negative (-) terminal, and apply about 12 V between SLL+-SLS- terminals.

  1. Check that operation noise can be heard from the solenoid.
    If the solenoid does not operate, replace the solenoid.