Home › TRANSMISSION · U151E AUTOMATIC TRANSAXLE › AUTOMATIC TRANSAXLE UNIT

AUTOMATIC TRANSAXLE UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    D009644E02
  1. Remove the nut, washer and control shaft lever.



    D009643E01
  1. Using a screwdriver, unstake the nut stopper, and remove the lock nut and nut stopper.



    D009639E01
  1. Remove the 2 bolts and pull out the park/neutral position switch.



2. REMOVE BREATHER PLUG HOSE
  1. Remove the breather plug hose from the transaxle case.



3. REMOVE OIL COOLER TUBE UNION (INLET OIL COOLER UNION)


    C083143E01
  1. Remove the union.

  1. Remove the O-ring from the union.



4. REMOVE OIL COOLER TUBE UNION (OUTLET OIL COOLER UNION)


    C083144E01
  1. Remove the elbow.

  1. Remove the O-ring from the elbow.



5. REMOVE SPEED SENSOR


    D030672E01
  1. Remove the 2 bolts and the 2 speed sensors from the transaxle assembly.



6. REMOVE TRANSAXLE CASE NO.1 PLUG


    D026716
  1. Remove the 4 transaxle case No.1 plugs from the transaxle case.

  1. Remove the 4 O-rings from the 4 transaxle case No.1 plugs.



7. FIX AUTOMATIC TRANSAXLE ASSEMBLY


    D009176
  1. Fix the transaxle assembly.



8. REMOVE AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY


    C091925
  1. Remove the 18 bolts, oil pan and gasket.



    C086316E02
  1. Remove the 2 magnets from the oil pan.



9. INSPECT TRANSMISSION OIL CLEANER MAGNET


    AT00103E03
  1. Remove the magnets and use them to collect any steel chips. Examine the chips and particles in the pan and on the magnet to determine what type of wear has occurred in the transaxle:

    Result:
    Steel (magnetic):
    Wear of the bearing, gear and plate
    Brass (non-magnetic):
    Wear of the bushing



10. DISCONNECT TRANSMISSION WIRE


    C091927E02
  1. Remove the 7 connectors from the shift solenoid valves.

  1. Remove the bolt, lock plate and temperature sensor.



11. REMOVE TRANSMISSION WIRE


    D003547E05
  1. Remove the bolt and transmission wire from the transaxle case.



12. REMOVE VALVE BODY OIL STRAINER ASSEMBLY


    C091931
  1. Remove the 3 bolts and oil strainer.



    C091932E01
  1. Remove the O-ring from the oil strainer.



13. REMOVE TRANSMISSION VALVE BODY ASSEMBLY


    C091933
  1. Support the valve body assembly and remove the 17 bolts and valve body assembly.



14. REMOVE GOVERNOR APPLY GASKET NO.1


    C083127
  1. Remove the governor apply gasket No.1 from the transaxle case.



15. REMOVE TRANSAXLE CASE 2ND BRAKE GASKET


    C083128
  1. Remove the transaxle case 2nd brake gasket from the transaxle case.



16. REMOVE BRAKE DRUM GASKET


    C083129
  1. Remove the brake drum gasket from the transaxle case.



17. REMOVE CHECK BALL BODY


    D003554E01
  1. Remove the check ball body and spring from the transaxle case.



18. REMOVE C-3 ACCUMULATOR PISTON


    D003555
  1. Remove the spring from the C-3 accumulator piston.



    D003556E01
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the C-3 accumulator piston.

    NOTICE:
    1. Applying compressed air may cause the piston to jump-out. When removing the piston, hold it using a waste cloth.
    2. Take care not to splash ATF when applying compressed air.



    D003902E01
  1. Remove the O-ring from the C-3 accumulator piston.



19. REMOVE REVERSE CLUTCH ACCUMULATOR PISTON


    D026401
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the reverse accumulator piston and spring.

    NOTICE:
    1. Applying compressed air may cause the piston to jump-out. When removing the piston, hold it using a waste cloth.
    2. Take care not to splash ATF when applying compressed air.



    D026402E04
  1. Remove the 2 O-rings from the reverse clutch accumulator piston.



20. REMOVE B-3 ACCUMULATOR PISTON


    D003558E01
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the B-3 accumulator piston and 2 springs.

    NOTICE:
    1. Applying compressed air may cause the piston to jump-out. When removing the piston, hold it using a waste cloth.
    2. Take care not to splash ATF when applying compressed air.



    D003904E01
  1. Remove the O-ring from the B-3 accumulator piston.



21. REMOVE MANUAL VALVE LEVER SHAFT RETAINER SPRING


    D003559
  1. Using needle-nose pliers, remove the manual valve lever shaft retainer spring.



22. REMOVE MANUAL DETENT SPRING SUB-ASSEMBLY


    D003560
  1. Remove the 2 bolts, the manual detent spring sub-assembly and cover.



23. REMOVE PARKING LOCK PAWL BRACKET


    C056727
  1. Remove the 2 bolts and parking lock pawl bracket.



24. REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY


    D003563
  1. Using a chisel and hammer, cut off and remove the spacer.



    D003564
  1. Using a pin punch (φ35 mm) and hammer, drive out the pin.

    HINT:
    Slowly drive out the pin so that it will not fall into the transaxle case.



    D003565
  1. Remove the manual valve lever shaft and manual valve lever.



25. REMOVE PARKING LOCK ROD SUB-ASSEMBLY


    D026382E01
  1. Remove the parking lock rod from the manual valve lever.



26. REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL


    D003566E01
  1. Using a screwdriver, remove the oil seal from the transaxle case.

    NOTICE:
    Do not apply excessive force when removing the oil seal.



27. FIX AUTOMATIC TRANSAXLE ASSEMBLY
  1. Fix the transaxle case with the oil pump side facing up.



28. INSPECT INPUT SHAFT ENDPLAY

HINT:



29. REMOVE TRANSAXLE HOUSING


    C115282
  1. Remove the 16 bolts.

  1. Tap on the circumference of the transaxle housing with a plastic hammer to remove the transaxle housing from the transaxle case.

    NOTICE:
    The differential may be accidentally removed when the transaxle housing is removed.



30. REMOVE OIL PUMP ASSEMBLY


    D003569E05
  1. Remove the 7 bolts and oil pump from the transaxle case.



31. REMOVE THRUST NEEDLE ROLLER BEARING


    D025505E02
  1. Remove the thrust needle roller bearing from the underdrive planetary gear assembly.



32. REMOVE THRUST BEARING UNDERDRIVE RACE NO.2


    D025506E03
  1. Remove the thrust bearing underdrive race No.2 from the underdrive planetary gear assembly.



33. REMOVE DIFFERENTIAL GEAR ASSEMBLY


    D026450E04
  1. Remove the differential gear assembly from the transaxle case.



34. REMOVE OVERDRIVE BRAKE GASKET


    D003573
  1. Remove the 2 overdrive brake gaskets from the transaxle case.



35. REMOVE FORWARD CLUTCH ASSEMBLY


    D003574E02
  1. Remove the forward clutch assembly from the transaxle case.



    D003906E01
  1. Remove the thrust needle roller bearing from the forward clutch.



36. REMOVE MULTIPLE DISC CLUTCH HUB


    D026787E03
  1. Remove the thrust needle roller bearing, multiple disc clutch hub, thrust needle roller bearing and thrust bearing race No.1 from the transaxle case.



37. INSPECT MULTIPLE DISC CLUTCH CLUTCH HUB

HINT:



38. REMOVE UNDERDRIVE PLANETARY GEAR ASSEMBLY


    D003576E02
  1. Remove the bolt and pawl shaft clamp.



    D009652
  1. Remove the parking lock pawl shaft.



    D009689
  1. Push the parking lock pawl.

    HINT:
    Failure to do so will cause interference when the underdrive planetary gear is removed.



    D003579E03
  1. Remove the underdrive planetary gear assembly from the transaxle case.

    NOTICE:
    Be careful so that the underdrive planetary gear assembly will not fall out.



39. REMOVE PARKING LOCK PAWL


    D026386
  1. Remove the spring, pawl pin and parking lock pawl.



40. REMOVE UNDERDRIVE CLUTCH ASSEMBLY


    D003580E01
  1. Remove the underdrive clutch assembly, thrust bearing and bearing race from the transaxle case.



41. REMOVE UNDERDRIVE 1-WAY CLUTCH ASSEMBLY


    D003581E01
  1. Using a screwdriver, remove the snap ring from the transaxle case.

    NOTICE:
    Do not apply excessive force when removing the snap ring.



    D003627E01
  1. Remove the underdrive 1-way clutch from the transaxle case.



    D003907E01
  1. Remove the outer race retainer from the 1-way clutch.



42. REMOVE UNDERDRIVE CLUTCH DISC NO.2


    D026466E01
  1. Using a screwdriver, remove the snap ring.

    NOTICE:
    Do not apply excessive force when removing the snap ring.



    D026385E01
  1. Remove the flange, 4 discs and 4 plates from the transaxle case.



43. INSPECT UNDERDRIVE CLUTCH DISC NO.2

HINT:



44. REMOVE TRANSAXLE REAR COVER SUB-ASSEMBLY


    D026387E02
  1. Remove the 11 bolts.

  1. Tap on the circumference of the rear cover with a plastic hammer to remove the transaxle rear cover from the transaxle case.



45. REMOVE TRANSAXLE CASE NO.1 PLUG


    D026388
  1. Remove the 4 transaxle case No.1 plugs from the transaxle rear cover.

  1. Remove the 4 O-rings from the 4 transaxle case No.1 plugs.



46. REMOVE REAR CLUTCH OIL SEAL RING OUTER


    D026389E01
  1. Remove the 3 rear clutch oil seal rings from the transaxle rear cover.



47. REMOVE NEEDLE-ROLLER BEARING


    D026472E01
  1. Using SST, remove the needle-roller bearing from the transaxle rear cover.

    SST
    09387-00041   (09387-01021, 09387-01030, 09387-01040)



48. REMOVE GOVERNOR APPLY GASKET NO.1


    D026390
  1. Using a screwdriver, remove the 3 apply gaskets.



49. REMOVE BRAKE APPLY TUBE


    D026391E03
  1. Remove the bolt, clamp and brake apply tube.

  1. Remove the clutch apply tube.

  1. Remove the brake apply tube from the clamp.

    NOTICE:
    Do not bend the tubes.



50. REMOVE DIRECT CLUTCH ASSEMBLY


    D026403E02
  1. Remove the thrust bearing and the direct clutch assembly from the transaxle case.



51. REMOVE OVERDRIVE DIRECT CLUTCH HUB SUB-ASSEMBLY


    D026392E03
  1. Remove the thrust bearing race, thrust bearing and overdrive direct clutch hub from the planetary gear assembly.



52. INSPECT OVERDRIVE DIRECT CLUTCH DRUM SUB-ASSEMBLY

HINT:



53. REMOVE REAR PLANETARY SUN GEAR ASSEMBLY


    D026714E02
  1. Remove the rear planetary sun gear assembly from the transaxle case.



    D026404E03
  1. Remove the thrust needle roller bearing and thrust bearing race from the rear planetary sun gear assembly.



    D026393E01
  1. Remove the planetary carrier thrust washer No.2 from the rear planetary sun gear assembly.



54. REMOVE 1-WAY CLUTCH ASSEMBLY


    D026598E02
  1. Remove the 1-way clutch assembly and the thrust needle roller bearing from the transaxle case.



    D003909E01
  1. Remove the 1-way clutch inner race from the 1-way clutch assembly.



55. REMOVE 1-WAY CLUTCH SLEEVE OUTER


    D003589E02
  1. Remove the 1-way clutch sleeve outer from the transaxle case.



56. REMOVE PLANETARY CARRIER THRUST WASHER NO.1


    D026394E02
  1. Remove the planetary carrier thrust washer No.1 from the planetary gear assembly.



57. REMOVE 2ND BRAKE CLUTCH DISC


    D026395E01
  1. Using a screwdriver, remove the snap ring.

  1. Remove the flange, 4 discs and 4 plates from the transaxle case.



58. INSPECT 2ND BRAKE CLUTCH DISC

HINT:



59. REMOVE 2ND BRAKE PISTON ASSEMBLY


    D008058E01
  1. Using a screwdriver, remove the snap ring.



    D026396E04
  1. Remove the 2ND brake piston assembly from the transaxle case.



60. REMOVE REAR PLANETARY GEAR ASSEMBLY


    D003616E01
  1. Using a screwdriver, remove the snap ring.



    D026591E02
  1. Remove the rear planetary gear assembly from the transaxle case.



61. REMOVE INPUT SUN GEAR


    D003873E02
  1. Remove the 2 thrust needle roller bearings, thrust bearing race No.2 and the input sun gear from the transaxle case.



62. REMOVE 1ST AND REVERSE BRAKE CLUTCH DISC


    D026397
  1. Remove the flange, 6 discs and 6 plates from the transaxle case.



63. INSPECT 1ST AND REVERSE BRAKE CLUTCH DISC

HINT:



64. REMOVE FRONT PLANETARY GEAR ASSEMBLY


    D003595E01
  1. Using a chisel and hammer, unstake the lock washer.

    NOTICE:
    Push down all claws of the washer. Otherwise the SST cannot be fully pressed against the nut, and cannot loosen the nut.



    D003596E01
  1. Using SST, remove the nut.

    SST
    09387-00030  
    09387-00080  



    D026398E01
  1. Using SST and a press, remove the front planetary gear assembly from the counter drive gear.

    SST
    09950-60010   (09951-00450)
    09950-70010   (09951-07100)



    D026763E01
  1. Remove the front planetary gear assembly from the brake hub.



65. REMOVE FRONT PLANETARY RING GEAR


    D003615E02
  1. Using a screwdriver, remove the snap ring and front planetary ring gear from the brake hub.



66. REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY


    D003600E01
  1. Place SST on the return spring, and compress the return spring with a press.

    SST
    09387-00070  

  1. Using a snap ring expander, remove the snap ring.

    NOTICE:
    1. Stop the press when the spring seat is lowered 1 to 2 mm (0.039 to 0.078 in.) from the snap ring groove, to prevent the spring seat from being deformed.
    2. Do not expand the snap ring excessively.



67. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

HINT:



68. REMOVE 1ST AND REVERSE BRAKE PISTON


    D026405E01
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transaxle case to remove the 1st and reverse brake piston.

    NOTICE:
    1. Applying compressed air may cause the piston to jump-out. When removing the piston, hold it using a waste cloth.
    2. Take care not to splash ATF when applying compressed air.



    D026713E01
  1. Remove the 2 O-rings from the 1st and reverse brake piston.



69. REMOVE COUNTER DRIVE GEAR


    C089120E01
  1. Using SST and a press, remove the counter drive gear from the transaxle case.

    SST
    09950-60010   (09951-00590)
    09950-70010   (09951-07100)



    D003602E01
  1. As shown in the illustration, tighten the 2 bolts evenly and make clearance of approx. 20.0 mm (0.787 in.) between the counter drive gear and the inner race.



    D003603E01
  1. Using SST, remove the tapered roller bearing.

    SST
    09950-60010   (09951-00590)
    09950-00020  
    09950-00030  
    09950-40011   (09957-04010)



70. REMOVE TRANSFER DRIVEN PINION FRONT BEARING


    D026467E01
  1. Using a snap ring expander, remove the snap ring.



    C089121E01
  1. Using SST and a press, remove the bearing outer race.

    SST
    09950-60020   (09951-00910)



71. REMOVE BREATHER PLUG NO.2 (ATM)


72. REMOVE UNDERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY


    D026407E01
  1. Place SST on the return spring, and compress the return spring with a press.

    SST
    09387-00020  

  1. Using a snap ring expander, remove the snap ring.

    NOTICE:
    1. Stop the press when the spring seat is lowered 1 to 2 mm (0.039 to 0.078 in.) from the snap ring groove, to prevent the spring seat from being deformed.
    2. Do not expand the snap ring excessively.



73. INSPECT UNDERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY

HINT:



74. REMOVE UNDERDRIVE BRAKE PISTON


    D026406E01
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transaxle case to remove the underdrive brake piston.



    D003794E01
  1. Remove the 2 O-rings from the underdrive brake piston.



75. REMOVE NEEDLE ROLLER BEARING


    D003605E01
  1. Using SST, remove the needleroller bearing from the transaxle case.

    SST
    09387-00041   (09387-01010, 09387-01030, 09387-01040)



76. REMOVE UNDERDRIVE CLUTCH DRUM OIL SEAL RING


    D003914E01
  1. Remove the 2 oil seal rings from the transaxle case.



77. REMOVE TRANSAXLE CASE NO.1 PLUG


    D026383
  1. Remove the 2 transaxle case No.1 plugs.

  1. Remove the 2 O-rings from the 2 transaxle case No.1 plugs.



78. REMOVE UNDERDRIVE CYLINDRICAL ROLLER BEARING


    D003606E01
  1. Using SST, remove the underdrive cylindrical roller bearing from the transaxle case.

    SST
    09514-35011  



79. REMOVE UNDERDRIVE OUTPUT SHAFT OIL SEAL RING


    D003915E05
  1. Remove the oil seal ring from the transaxle housing.



80. REMOVE DIFFERENTIAL GEAR LUBE APPLY TUBE


    D026400E02
  1. Remove the bolt, transaxle apply tube clamp and differential gear lube apply tube from the transaxle housing.

    NOTICE:
    Do not bend the tubes.