Home › TRANSMISSION ยท U151F AUTOMATIC TRANSAXLE › OIL PUMP

OIL PUMP > INSPECTION

for Preparation Click here



1. INSPECT OIL PUMP ASSEMBLY


    D009205
  1. Turn the drive gear with the 2 screwdrivers and make sure that it rotates smoothly.

    NOTICE:
    Be careful not to damage the oil seal lip.



2. INSPECT CLEARANCE OF OIL PUMP ASSEMBLY


    D009207E01
  1. Push the driven gear to one side of the body.

  1. Using a feeler gauge, measure the clearance.

    Standard body clearance:
    0.10 to 0.17 mm (0.0039 to 0.0067 in.)

    Side clearance:
    0.02 to 0.05 mm (0.001 to 0.002 in.)

    Maximum body clearance:
    0.17 mm (0.0067 in.)

    If the body clearance is greater than the maximum, replace the oil pump body sub-assembly.



    D009208
  1. Using a feeler gauge, measure the tip clearance between the driven gear teeth and drive gear teeth.

    Standard tip clearance:
    0.07 to 0.15 mm (0.0028 to 0.0059 in.)
    Maximum tip clearance:
    0.15 mm (0.0059 in.)

    If the tip clearance is greater than the maximum, replace the oil pump body sub-assembly.



    D009209
  1. Using a straightedge and feeler gauge, measure the side clearance of both gears.

    Standard side clearance:
    0.02 to 0.05 mm (0.0008 to 0.0020 in.)
    Maximum side clearance:
    0.05 mm (0.0020 in.)

    Drive gear thickness: mm (in.) 
    Mark
    Thickness
    A
    11.690 to 11.699 (0.4602 to 0.4606)
    B
    11.700 to 11.709 (0.4606 to 0.4610)
    C
    11.710 to 11.720 (0.4610 to 0.4614)
    D
    11.721 to 11.730 (0.4615 to 0.4618)
    E
    11.731 to 11.740 (0.4619 to 0.4622)
    Driven gear thickness: mm (in.) 
    Mark
    Thickness
    A
    11.690 to 11.699 (0.4602 to 0.4606)
    B
    11.700 to 11.709 (0.4606 to 0.4610)
    C
    11.710 to 11.720 (0.4610 to 0.4614)
    D
    11.721 to 11.730 (0.4615 to 0.4618)
    E
    11.731 to 11.740 (0.4619 to 0.4622)



3. INSPECT FRONT OIL PUMP AND GEAR BODY SUB-ASSEMBLY


    D003648
  1. Using a dial indicator, measure the inside diameter of the oil pump body bushing.

    Standard inside diameter:
    38.113 to 38.138 mm (1.50051 to 1.50149 in.)
    Maximum inside diameter:
    38.188 mm (1.50346 in.)

    If the inside diameter is greater than the maximum, replace the oil pump body sub-assembly.



4. INSPECT STATOR SHAFT ASSEMBLY


    D003653
  1. Using a dial indicator, measure the inside diameter of the stator shaft.

    Standard inside diameter:
    21.500 to 21.526 mm (0.84646 to 0.84748 in.)
    Maximum inside diameter:
    21.57 mm (0.8492 in.)

    If the inside diameter is greater than the maximum, replace the stator shaft.