Home › BODY ELECTRICAL › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM

WIRELESS DOOR LOCK CONTROL SYSTEM > TERMINALS OF ECU

for Preparation Click here



INSTRUMENT PANEL JUNCTION BLOCK (MULTIPLEX NETWORK BODY ECU)
  1. Disconnect the B6, B7 and B9 ECU connectors.



  2. Disconnect the 1A, 1C, 1K, 1L and 1P J/B connectors.


    B067998E01

  3. Check the voltage or resistance according to the value(s) in the table below (wire harness side connector).

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    IG (1A-1) - Body ground
    W - Body ground
    +B (power system, generator system) power supply
    Always
    10 to 14 V
    ACC (1A-1) - Body ground
    W - Body ground
    +B (power system, generator system) power supply
    Always
    10 to 14 V
    BECU (1C-24) - Body ground
    W-L - Body ground
    +B (BECU) power supply
    Always
    10 to 14 V
    ALTB (1C-30) - Body ground
    B - Body ground
    +B (power system, generator system) power supply
    Always
    10 to 14 V
    GND1 (1L-16) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    GND2 (1K-17) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    LCTY (1P-19) - Body ground
    GR - Body ground
    Rear courtesy light switch LH input
    Rear door LH closed → opened
    10 kΩ or higher → Below 1 Ω
    KSW (B6-21) - Body ground
    L-B - Body ground
    Unlock warning switch input
    No key in ignition key cylinder → key inserted
    10 kΩ or higher → Below 1 Ω
    PCTY (B7-23) - Body ground
    R-Y - Body ground
    Passenger side courtesy light switch input
    Passenger side door closed → opened
    10 kΩ or higher → Below 1 Ω
    BCTY (B7-25) - Body ground
    G-W - Body ground
    Back door courtesy light switch input
    Back door closed → opened
    10 kΩ or higher → Below 1 Ω
    DCTY (B9-14) - Body ground
    R-Y - Body ground
    Driver side courtesy light switch input
    Driver side door closed → opened
    10 kΩ or higher → Below 1 Ω
    RCTY (B9-16) - Body ground
    R-W - Body ground
    Rear courtesy light switch RH input
    Rear door RH closed → opened
    10 kΩ or higher → Below 1 Ω

    HINT:
    If the result is not as specified, there may be a malfunction on the wire harness side.

  4. Reconnect the B6, B7 and B9 ECU connectors.

  5. Reconnect the 1A, 1C, 1K, 1L and 1P J/B connectors.

  6. Check the voltage according to the value(s) in the table below (ECU side connector).

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    HAZ (B6-2) - Body ground
    G-O - Body ground
    Hazard warning light signal
    Answer-back OFF → answer-back ON
    Below 1 V → Pulse generation
    BZR (B8-2) - Body ground
    G - Body ground
    Wireless door lock buzzer
    Wireless door lock buzzer OFF → ON
    Below 1 V → Pulse generation
    RDA (B9-12) - Body ground
    P-L - Body ground
    Door control receiver input
    No key in ignition key cylinder, all doors closed and transmitter switch OFF → ON
    Below 1 V → Approx. 6 to 7 → Below 1 V
    If the result is not as specified, the instrument panel J/B (multiplex network body ECU) may have a malfunction.