Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION SYSTEM

NAVIGATION SYSTEM > Illumination Circuit

for Preparation Click here


DESCRIPTION

Power is supplied to the navigation receiver assembly and steering pad switch illumination when the light control switch is in the TAIL or HEAD position.

WIRING DIAGRAM


E147244E02


INSPECTION PROCEDURE

NOTICE:
The vehicle is equipped with an SRS (Supplemental Restraint System) such as the airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the Supplemental Restraint System (Click here).

1.CHECK ILLUMINATION
  1. Check if the illumination for the navigation receiver assembly, steering pad switch, glove box or others (Hazard switch, cigarette lighter, etc.) comes on when the light control switch is turned to the HEAD or TAIL position.

    Result:

    Condition
    Proceed to
    Illumination comes on for all components except steering pad switch.
    A
    Illumination comes on for all components except navigation receiver assembly.
    B
    No illumination comes on (navigation receiver assembly, hazard switch, glove box, etc.)
    C
    Illumination comes on only for glove box and steering pad switch.
    D



B
Go to step 7

C
GO TO LIGHTING SYSTEM

D
GO TO METER / GAUGE SYSTEM
A


2.CHECK HARNESS AND CONNECTOR (BATTERY - SPIRAL CABLE SUB-ASSEMBLY)


    E120026E02
  1. Disconnect the spiral cable sub-assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester connection
    Condition
    Specified condition
    ILL+ - Body ground
    Light control switch TAIL or HEAD
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK STEERING PAD SWITCH ASSEMBLY


  1. Disconnect the steering pad switch assembly connector.


    E120115E01

  1. Disconnect the steering pad switch connector.

  1. Connect the positive (+) lead to terminal ILL+ and the negative (-) lead to terminal EAU of the steering pad switch connector.

  1. Check if the illumination for the steering pad switch comes on.

    Result
    Proceed to
    Illumination does not come on for either the steering pad switch LH RH.
    A
    Illumination comes on for only the steering pad switch LH.
    B
    Illumination comes on for only the steering pad switch RH.
    C



B
Go to step 6

C
REPLACE STEERING PAD SWITCH LH
A


4.INSPECT SPIRAL CABLE SUB-ASSEMBLY


    E113447E04
  1. Disconnect the steering pad switch and spiral cable sub-assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Spiral Cable Position
    Specified Condition
    EAU - EAU
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    ILL+ - ILL+
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right

    NOTICE:
    The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the page shown in the brackets .



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY
OK


5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY)


    E120116E08
  1. Disconnect the connectors from the navigation receiver assembly and spiral cable sub-assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    SWG - EAU
    Always
    Below 1 Ω
    SWG - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE NAVIGATION RECEIVER ASSEMBLY 

6.INSPECT STEERING PAD SWITCH CABLE


  1. Disconnect the steering pad switch LH and the steering pad switch RH.


    E120113E03

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Tester connection
    Condition
    Specified condition
    LH-1 - RH-1
    Always
    Below 1 Ω
    LH-2 - RH-2
    Always
    Below 1 Ω
    LH-3 - RH-3
    Always
    Below 1 Ω
    LH-4 - RH-4
    Always
    Below 1 Ω
    LH-5 - RH-5
    Always
    Below 1 Ω
    LH-6 - RH-6
    Always
    Below 1 Ω
    LH-7 - RH-7
    Always
    Below 1 Ω
    LH-8 - RH-8
    Always
    Below 1 Ω
    LH-1 - Body ground
    Always
    10 kΩ or higher
    LH-2 - Body ground
    Always
    10 kΩ or higher
    LH-3 - Body ground
    Always
    10 kΩ or higher
    LH-4 - Body ground
    Always
    10 kΩ or higher
    LH-5 - Body ground
    Always
    10 kΩ or higher
    LH-6 - Body ground
    Always
    10 kΩ or higher
    LH-7 - Body ground
    Always
    10 kΩ or higher
    LH-8 - Body ground
    Always
    10 kΩ or higher



NG
REPLACE STEERING PAD SWITCH CABLE
OK

REPLACE STEERING PAD SWITCH RH 

7.CHECK HARNESS AND CONNECTOR (BATTERY - NAVIGATION RECEIVER ASSEMBLY)


    E113513E02
  1. Disconnect the navigation receiver assembly connector R15.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester connection
    Condition
    Specified condition
    ILL+ - Body ground
    Light control switch
    TAIL or HEAD
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER)


    E125113E03
  1. Disconnect the navigation receiver assembly and combination meter connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard voltage:
    Tester connection
    Condition
    Specified condition
    ILL- - C10-22
    Always
    Below 1 Ω
    ILL- - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE