Home › BODY › MIRROR › POWER MIRROR CONTROL SYSTEM (w/ Memory)

POWER MIRROR CONTROL SYSTEM (w/ Memory) > DATA LIST / ACTIVE TEST

for Preparation Click here



USING TECHSTREAM
  1. Connect Techstream to the DLC3.

  2. Monitor the ECU data by following the prompts on the tester screen.

    HINT:
    Techstream has a "Snapshot" function which records the monitored data. Refer to Techstream operator's manual for further details.


DATA LIST

HINT:
Using the DATA LIST displayed on Techstream, you can read the value of the switch, sensor, actuator, etc. without parts removal. Reading the DATA LIST as the first step of troubleshooting is one way to shorten the labor time.

  1. Connect Techstream to the DLC3.

  2. Ignition switch on.

  3. Read the DATA LIST according to the display on the tester.

    Mirror L/Mirror R:

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Mir Position Sensor (V)
    Vertical mirror position/MIN: 0, MAX 5 V
    Within range from 0 to 5 V
    -
    Mir Position Sensor (H)
    Horizontal mirror position/MIN: 0, MAX 5 V
    Within range from 0 to 5 V
    -
    Mirror Memory No1
    Mirror position memorized in memory switch M1/NOT MEM or MEM
    MEM: Memorized
    NOT MEM: Not memorized
    -
    Mirror Memory No2
    Mirror position memorized in memory switch M2/NOT MEM or MEM
    MEM: Memorized
    NOT MEM: Not memorized
    -
    Mirror Memory No3
    Mirror position memorized in memory switch M3/NOT MEM or MEM
    MEM: Memorized
    NOT MEM: Not memorized
    -
    Foot Light Setup
    Foot light (puddle light) illumination time
    OFF/7.5S/15S/30S
    -


    Driver Seat:

    Tester Display
    Measurement Item/Range
    Normal Condition
    Normal Condition
    Power Voltage
    Power supply for position control ECU & switch/MIN: 0 V, MAX: 19.89 V
    Within range from 11 to 14 V
    -
    Ignition switch
    Ignition switch status/ON or OFF
    ON: Ignition switch is ON
    OFF: Ignition switch is OFF
    -
    KSW Switch
    Key unlock warning switch signal/ON or OFF
    ON: Key is in ignition key cylinder
    OFF: Key is not in ignition key cylinder
    -
    P Switch
    Park/Neutral position switch signal/ON or OFF
    ON: Shift in P position
    OFF: Shift in any position except neutral
    -
    M1 Switch
    Seat memory switch M1 signal/ON or OFF
    ON: Seat memory switch M1 is ON
    OFF: Seat memory switch M1 is OFF
    -
    M2 Switch
    Seat memory switch M2 signal/ON or OFF
    ON: Seat memory switch M2 is ON
    OFF: Seat memory switch M2 is OFF
    -
    M3 Switch
    Seat memory switch M3 signal/ON or OFF
    ON: Seat memory switch M3 is ON
    OFF: Seat memory switch M3 is OFF
    -
    SET Switch
    Seat memory set switch signal/ON or OFF
    ON: Memory set switch is ON
    OFF: Memory set switch is OFF
    -
    Memory No1
    Driving position memorized in seat memory switch M1/NOT MEM or MEM
    MEM: Memorized
    NOT MEM: Not memorized
    -
    Memory No2
    Driving position memorized in seat memory switch M2/NOT MEM or MEM
    MEM: Memorized
    NOT MEM: Not memorized
    -
    Driver Mirror Mem No1
    Driver side mirror position memorized in seat memory switch M1/NOT MEM or MEM
    MEM: Memorized
    NOT MEM: Not memorized
    -
    Driver Mirror Mem No2
    Driver side mirror position memorized in seat memory switch M2/NOT MEM or MEM
    MEM: Memorized
    NOT MEM: Not memorized
    -
    Passenger Mirror Mem No1
    Passenger side mirror position memorized in seat memory switch M1/NOT MEM or MEM
    MEM: Memorized
    NOT MEM: Not memorized
    -
    Passenger Mirror Mem No2
    Passenger side mirror position memorized in seat memory switch M2/NOT MEM or MEM
    MEM: Memorized
    NOT MEM: Not memorized
    -
    Otr(D) Mir Pos Mem No1
    Driver side mirror position memorized in seat memory switch M1/MIN: 0, MAX: 65535
    Within range from 0 to 65535
    -
    Otr(P) Mir Pos Mem No1
    Passenger side mirror position memorized in seat memory switch M1/MIN: 0, MAX: 65535
    Within range from 0 to 65535
    -
    Otr(D) Mir Pos Mem No2
    Driver side mirror position memorized in seat memory switch M2/MIN: 0, MAX: 65535
    Within range from 0 to 65535
    -
    Otr(P) Mir Pos Mem No2
    Passenger side mirror position memorized in seat memory switch M2/MIN: 0, MAX: 65535
    Within range from 0 to 65535
    -
    Otr(D) Mir Pos Mem No3
    Driver side mirror position memorized in seat memory switch M3/MIN: 0, MAX: 65535
    Within range from 0 to 65535
    -
    Otr(P) Mir Pos Mem No3
    Passenger side mirror position memorized in seat memory switch M3/MIN: 0, MAX: 65535
    Within range from 0 to 65535
    -


    Body:

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Mirror Selection SW (R)
    Mirror selection switch signal for RH mirror/ON or OFF
    ON: Switch is in Right position
    OFF: Switch is in neutral or Left position
    -
    Mirror Selection SW (L)
    Mirror selection switch signal for LH mirror/ON or OFF
    ON: Switch is in Left position
    OFF: Switch is in neutral or Right position
    -
    Mirror Position SW (R)
    Mirror position switch signal (Right)/ON or OFF
    ON: Switch R is ON
    OFF: Any switch except R is ON or all switches are OFF
    -
    Mirror Position SW (L)
    Mirror position switch signal (Left)/ON or OFF
    ON: Switch L is ON
    OFF: Any switch except L is ON or all switches are OFF
    -
    Mirror Position SW (Up)
    Mirror position switch signal (Up)/ON or OFF
    ON: Switch UP is ON
    OFF: Any switch except UP is ON or all switches are OFF
    -
    Mirror Position SW (Dwn)
    Mirror position switch signal (Down)/ON or OFF
    ON: Switch DOWN is ON
    OFF: Any switch except DOWN is ON or all switches are OFF
    -


ACTIVE TEST

HINT:
Performing the ACTIVE TEST using Techstream allows you to operate the relay, VSV, actuator, etc. without parts removal. Performing the ACTIVE TEST as the first step of troubleshooting is one way to shorten the labor time. It is possible to display the DATA LIST during the ACTIVE TEST.

  1. Connect Techstream to the DLC3.

  2. Ignition switch on.

  3. Perform the ACTIVE TEST according to the display on the tester.

    Mirror L/Mirror R:

    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Mirror Up/Down
    Mirror vertical operation:
    UP/DOWN
    -
    Mirror Right/Left
    Mirror horizontal operation:
    RIGHT/LEFT
    -
    Mirror heater
    Mirror heater operation:
    OFF/ON
    -
    Foot Light
    Foot light illumination operation
    ON/OFF
    -