ENGINE IMMOBILISER SYSTEM > TERMINALS OF ECU |
| CHECK TRANSPONDER KEY AMPLIFIER |

Disconnect the I14 amplifier connector and measure the resistance between the terminal of the wire harness side connector and body ground.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| GND (I14-7) - Body ground | BR-R - Body ground | Ground | Always | Below 1 Ω |
Reconnect the I14 amplifier connector and measure the resistance and voltage of each terminal of the connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| VC5 (I14-1) - GND (I14-7) | Y-B - BR-R | Power source | No key is in ignition key cylinder | Below 1 V |
| Key is in ignition key cylinder | 4.6 to 5.4 V | |||
| CODE (I14-4) - GND (I14-7) | Y - BR-R | Demodulated signal of key code date | No key is in ignition key cylinder | Below 1 V |
| Key is in ignition key cylinder | Waveform 1 | |||
| TXCT (I14-5) - GND (I14-7) | Y-R - BR-R | Key code output signal | No key is in ignition key cylinder | Below 1 V |
| Key is in ignition key cylinder | Waveform 2 | |||
| GND (I14-7) - Body ground | BR-R - Body ground | Ground | Always | Below 1 Ω |
Inspect using an oscilloscope.
![]() |
Waveform 1 (Reference):
| Terminal | CODE - GND |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Key is in ignition key cylinder |
![]() |
Waveform 2 (Reference):
| Terminal | TXCT - GND |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Key is in ignition key cylinder |
| CHECK TRANSPONDER KEY ECU ASSEMBLY |

Disconnect the T6 ECU connector and measure the resistance and voltage between each terminal of the wire harness side connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| +B (T6-1) - GND (T6-14) | W-L - W-B | Battery | Always | 10 to 14 V |
| IG (T6-2) - GND (T6-14) | B-O - W-B | Ignition switch | Ignition switch off | Below 1 V |
| Ignition switch on | 10 to 14 V | |||
| KSW (T6-10) - GND (T6-14) | L-W - W-B | Unlock warning switch | No key is in ignition key cylinder | 10 kΩ or higher |
| Key is in ignition key cylinder | Below 1 Ω |
Reconnect the T9 ECU connector and measure the voltage of each terminal of the connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| AGND (T6-13) - Body ground | BR-R - Body ground | Ground | Always | Below 1 Ω |
| KSW (T6-10) - GND (T6-14) | L-W - W-B | Unlock warning switch | No key is in ignition key cylinder | 10 to 14 V |
| Key is in ignition key cylinder | Below 1 V | |||
| VC5 (T6-8) - AGND (T6-13) | Y-B - BR-R | Power source | Ignition switch off | Below 1 V |
| Ignition switch on | 4.6 to 5.4 V | |||
| TXCT (T6-12) - AGND (T6-13) | Y-R - BR-R | Transponder key amplifier communication signal | No key is in ignition key cylinder | Below 1 V |
| Key is in ignition key cylinder | Waveform 1 | |||
| CODE (T6-11) - AGND (T6-13) | Y - BR-R | Transponder key amplifier ground | No key is in ignition key cylinder | Below 1 V |
| Key is in ignition key cylinder | Waveform 2 | |||
| EFIO (T6-6) - GND (T6-14) | BR-R - W-B | ECM output signal | Ignition switch off | Below 1 V |
| Ignition switch on | Waveform 3 | |||
| EFII (T6-7) - GND (T6-14) | BR-W - W-B | ECM input signal | Ignition switch off | Below 1 V |
| Ignition switch on | Waveform 4 |
Inspect using an oscilloscope.
![]() |
Wave form 1 (Reference):
| Terminal | TXCT - AGND |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Key is in ignition key cylinder |
![]() |
Wave form 2 (Reference):
| Terminal | CODE - AGND |
| Tool Setting | 10 V/DIV., 20 ms/DIV. |
| Condition | Key is in ignition key cylinder |
![]() |
Wave form 3 (Reference):
| Terminal | EFIO - AGND |
| Tool Setting | 5 V/DIV., 50 ms/DIV. |
| Condition | Ignition switch on |
![]() |
Wave form 4 (Reference):
| Terminal | EFII - AGND |
| Tool Setting | 5 V/DIV., 50 ms/DIV. |
| Condition | Ignition switch on |
| CHECK ECM |

Disconnect the E11 ECM connector and measure the resistance between the terminal of the wire harness side connector and body ground.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| E1 (E11-1) - Body ground | BR - Body ground | Ground | Always | Below 1 Ω |
Reconnect the E11 ECM. Measure the voltage between each terminal of the connector according to the value(s) in the table below.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| IMI (E5-16) - E1 (E11-1) | BR-R - BR | Transponder key ECU input signal | Ignition switch off | Below 1 V |
| Ignition switch on | Waveform 1 | |||
| IMO (E5-15) - E1 (E11-1) | BR-W - BR | Transponder key ECU output signal | Ignition switch off | Below 1 V |
| Ignition switch on | Waveform 2 |
Inspect using an oscilloscope.
![]() |
Waveform 1 (Reference):
| Terminal | IMI - E1 |
| Tool Setting | 5 V/DIV., 50 ms/DIV. |
| Condition | Ignition switch on |
![]() |
Waveform 2 (Reference):
| Terminal | IMO - E1 |
| Tool Setting | 5 V/DIV., 50 ms/DIV. |
| Condition | Ignition switch on |