Home › SECURITIES › ENGINE IMMOBILISER › ENGINE IMMOBILISER SYSTEM

DTC    B2796    No Communication in Immobiliser System

DTC    B2798    Communication Malfunction No. 2

for Preparation Click here


DESCRIPTION

These codes are stored in the memory when a key that does not have a transponder chip is inserted or if communication between the key and transponder key ECU is impossible.

DTC No.
DTC Detection Condition
Trouble Area
B2796
No communication
  1. Key
  2. Wire harness
  3. Transponder key amplifier
  4. Transponder key ECU assembly
B2798
Communication error
  1. Key

WIRING DIAGRAM


B111588E24


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM
  1. Connect Techstream to the DLC3.

  1. Turn the ignition switch on.

  1. Turn the tester on.

  1. Enter the following menus: Body Electrical / Immobiliser / Data List.

  1. Read the Data List according to the display on the tester.

    Immobiliser: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Immobiliser
    Immobiliser system status / SET or UNSET
    UNSET: Ignition switch on
    SET: Without key
    -

    OK:
    UNSET (Ignition switch on) appears on the screen.



OK
REPLACE TRANSPONDER KEY ECU ASSEMBLY
NG


2.CHECK KEYS
  1. Insert the vehicle's other key into the ignition key cylinder.

  1. Check that the engine starts with this key.

    OK:
    The engine starts



OK
RE-REGISTER OR REPLACE KEY
NG


3.READ VALUE USING TECHSTREAM
  1. Connect Techstream to the DLC3.

  1. Turn the ignition switch on.

  1. Turn the tester on.

  1. Enter the following menus: Body Electrical / Immobiliser / Data List.

  1. Read the Data List according to the display on the tester.

    Immobiliser: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Antenna Coil Status
    Antenna coil condition /NORMAL or FAIL
    NORMAL: Antenna coil is normal.
    FAIL: Antenna coil is malfunctioning.
    -

    OK:
    NORMAL (Antenna coil is normal) appears on the screen.



OK
REPLACE TRANSPONDER KEY ECU ASSEMBLY
NG


4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - TRANSPONDER KEY AMPLIFIER)


    B111591E06
  1. Disconnect the T6 ECU and I14 amplifier connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester Connection
    Specified Condition
    T6-8 (VC5) - I14-1 (VC5)
    Below 1 Ω
    T6-11 (CODE) - I14-4 (CODE)
    T6-12 (TXCT) - I14-5 (TXCT)
    T6-13 (AGND) - I14-7 (GND)
    T6-8 (VC5) - Body ground
    10 kΩ or higher
    T6-11 (CODE) - Body ground
    T6-12 (TXCT) - Body ground
    T6-13 (AGND) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT TRANSPONDER KEY ECU ASSEMBLY


    B111616E11
  1. Reconnect the T6 ECU and I14 amplifier connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Voltage:
    Tester Connection
    Condition
    Specified Condition
    T6-8 (VC5) - Body ground
    No key is in ignition key cylinder
    Below 1 V
    Key is in ignition key cylinder
    4.6 to 5.4 V

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester Connection
    Condition
    Specified Condition
    T6-13 (AGND) - Body ground
    Always
    Below 1 Ω



NG
REPLACE TRANSPONDER KEY ECU ASSEMBLY
OK


6.REPLACE TRANSPONDER KEY AMPLIFIER
  1. After replacing the transponder key amplifier with a normally functioning transponder key amplifier, check that the engine starts.

    OK:
    The engine starts.



NG
REPLACE TRANSPONDER KEY ECU ASSEMBLY
OK

END (TRANSPONDER KEY AMPLIFIER DEFECTIVE)