Home › SECURITIES › ENGINE IMMOBILISER › ENGINE IMMOBILISER SYSTEM

ENGINE IMMOBILISER SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



READ DATA LIST

HINT:
Using the Data List displayed on Techstream, you can read the value of the switch, sensor, actuator, etc. without parts removal. Reading the Data List as the first step in troubleshooting is one way to shorten the labor time.

  1. Connect Techstream to the DLC3.

  2. Turn the ignition switch on.

  3. Turn the tester on.

  4. Enter the following menus: Body Electrical / Immobiliser / Data List.

  5. Read the Data List according to the display on the tester.

    Immobiliser: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    KEY SW
    Unlock warning switch signal / ON or OFF
    ON: Key is in ignition key cylinder
    OFF: No key is in ignition key cylinder
    -
    IG SW
    Ignition switch signal / ON or OFF
    ON: Ignition switch on
    OFF: Ignition switch off
    -
    Immobiliser
    Immobiliser system status / SET or UNSET
    UNSET: Ignition switch on
    SET: Without key
    -
    Permit (Start)
    Permit (Start) signal/OK or NG
    NG: No permission for engine start
    OK: Engine start permission
    -
    Response
    Transponder chip data / NG or OK
    NG: Data error
    OK: Data OK
    -
    Frame Error
    Transponder chip data / NG or OK
    NG: Data error
    OK: Data OK
    -
    Frame Error
    Transponder chip data / NG or OK
    NG: Data error
    OK: Data OK
    -
    Different Encrypt Code
    Transponder chip data / NG or OK
    NG: Data error
    OK: Data OK
    -
    Abnormal Status
    Transponder chip data / NG or OK
    NG: Data error
    OK: Data OK
    -
    Bcc Malfunction
    Transponder chip data / NG or OK
    NG: Incorrect data being sent.
    OK: Correct data being sent.
    -
    Sub Key
    Sub key code signal / NOMATH or MATCH
    NOMATCH: Non matching sub key code is sent.
    MATCH: Sub key code is sent.
    -
    Master Key
    Master key code signal / NOMATH or MATCH
    NOMATCH: Non matching master key code is sent.
    MATCH: Master key code is sent.
    -
    Transponder S-Code
    Number of registered sub key / min. 0, max. 15
    Number of registered sub key.
    -
    Transponder M-Code
    Number of registered master key / min. 0, max. 15
    Number of registered master key.
    -
    Reg Code Space Full
    Memory space for key codes registration / NOT FUL or FULL
    NOT FUL: More key code registration possible.
    FULL: No more key code registration possible.
    -
    +B
    Power source / BRAKE or NORMAL
    BRAKE: Power source open.
    NORMAL: Power source normal.
    -
    Antenna Coil Status
    Antenna coil condition / NORMAL or FAIL
    NORMAL: Antenna coil is normal.
    FAIL: Antenna coil is malfunctioning.
    -


PERFORM Active Test

HINT:
Performing the Active Test using Techstream allows the relay, VSV, actuator, etc. to operate without removing any parts . Performing the Active Test as the first step of troubleshooting is one way to shorten labor time.

  1. Connect Techstream to the DLC3.

  2. Turn the ignition switch on.

  3. Turn the tester on.

  4. Enter the following menus: Body Electrical / Immobiliser / Active Test.

  5. Perform the Active Test according to the display on the tester.

    Immobiliser: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Security Indic
    Turn security indicator
    ON / OFF
    -