Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B0112/41    Short to GND in Side Squib RH Circuit

for Preparation Click here


DESCRIPTION

The side squib RH circuit consists of the center airbag sensor assembly and the front seat side airbag assembly RH.
The circuit instructs the SRS to deploy when deployment conditions are met.
DTC B0112/41 is recorded when a short to ground is detected in the side squib RH circuit.

DTC No.
DTC Detecting Condition
Trouble Area
B0112/41
  1. Short circuit in side squib RH wire harness (to ground)
  2. Side squib RH malfunction
  3. Center airbag sensor assembly malfunction
  1. Front seat side airbag assembly RH (Side squib RH)
  2. Center airbag sensor assembly
  3. Floor wire No. 2

WIRING DIAGRAM

Click here.

INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting the "check mode" (signal check) with the Techstream (Click here).
  2. After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).

1.CHECK FRONT SEAT SIDE AIRBAG ASSEMBLY RH (SIDE SQUIB RH)


    C110410E02
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the connectors from the front seat side airbag assembly RH.

  1. Connect SST (resistance 2.1 Ω) to the floor wire No. 2.

    CAUTION:
    Never connect a tester to the front seat side airbag assembly RH (side squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting.
    Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B0112/41 is not output.

    HINT:
    Codes other than DTC B0112/41 may be output at this time, but they are not related to this check.



NG
Go to step 2
OK

REPLACE FRONT SEAT ASSEMBLY RH 

2.CHECK FLOOR WIRE NO.2 (SIDE SQUIB RH CIRCUIT)


    C110406E41
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect SST (resistance 2.1 Ω) from the floor wire No. 2.

  1. Disconnect the connector from the center airbag sensor assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    S19-1 (SFR+) -
    Body ground
    Always
    1 MΩ or higher
    S19-2 (SFR-) -
    Body ground
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE NO.2
OK


3.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    C110411E01
  1. Connect the connectors to the front seat side airbag assembly RH and the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B0112/41 is not output.

    HINT:
    Codes other than code B0112/41 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK

USE SIMULATION METHOD TO CHECK