Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1141/33    Side Airbag Sensor Assembly LH Circuit Malfunction

for Preparation Click here


DESCRIPTION

The side airbag sensor LH circuit consists of the center airbag sensor assembly and side airbag sensor LH.
If the center airbag sensor assembly receives signals from the side airbag sensor LH, it judges whether or not the SRS should be activated.
DTC B1141/33 is recorded when a malfunction in the side airbag sensor LH circuit is detected.

DTC No.
DTC Detecting Condition
Trouble Area
B1141/33
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the side airbag sensor RH circuit for 2 seconds.
  2. Side airbag sensor LH malfunction
  3. Center airbag sensor assembly malfunction
  1. Side airbag sensor LH
  2. Center airbag sensor assembly
  3. Floor wire

WIRING DIAGRAM


H043054E34


INSPECTION PROCEDURE

1.CHECK DTC


    C110453E03
  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1141/33 is not output.

    HINT:
    Codes other than DTC B1141/33 may be output at this time, but they are not related to this check.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK 

2.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the side airbag sensor LH.

    OK:
    The connectors are connected.



NG
CONNECT CONNECTORS
OK


3.CHECK FLOOR WIRE (OPEN)


    C110448E11
  1. Disconnect the connectors from the center airbag sensor assembly and the side airbag sensor LH.

  1. Using a service wire, connect A20-16 (VUPL) and A20-18 (ESL) of connector "B".

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    S14-4 (VUPL) - S14-1 (ESL)
    Always
    Below 1 Ω



    C110447E11
  1. Using a service wire, connect A20-17 (SSL+) and A20-20 (SSL-) of connector "B".

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    S14-3 (SSL+) - S14-2 (SSL-)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE FLOOR WIRE
OK


4.CHECK FLOOR WIRE (SHORT TO B+)


    C109479E25
  1. Disconnect the service wire from connector "B".

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester connection
    Condition
    Specified condition
    S14-4 (VUPL) -
    Body ground
    Always
    Below 1 V
    S14-1 (ESL) -
    Body ground
    Always
    Below 1 V
    S14-3 (SSL+) -
    Body ground
    Always
    Below 1 V
    S14-2 (SSL-) -
    Body ground
    Always
    Below 1 V



NG
REPAIR OR REPLACE FLOOR WIRE
OK


5.CHECK FLOOR WIRE (SHORT TO GROUND)


    C109479E25
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    S14-4 (VUPL) -
    Body ground
    Always
    1 MΩ or higher
    S14-1 (ESL) -
    Body ground
    Always
    1 MΩ or higher
    S14-3 (SSL+) -
    Body ground
    Always
    1 MΩ or higher
    S14-2 (SSL-) -
    Body ground
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK


6.CHECK FLOOR WIRE (SHORT)


    C109479E25
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    S14-4 (VUPL) - S14-1 (ESL)
    Always
    1 MΩ or higher
    S14-3 (SSL+) - S14-2 (SSL-)
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK


7.CHECK SIDE AIRBAG SENSOR LH


    C157631E01
  1. Connect the connector to the center airbag sensor assembly.

  1. Interchange the side airbag sensor RH with LH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1140/32 and B1141/33 are not output.
    A
    DTC B1140/32 is output.
    B
    DTC B1141/33 is output.
    C

    HINT:
    Codes other than DTC B1140/32 and B1141/33 may be output at this time, but they are not related to this check.



B
REPLACE SIDE AIRBAG SENSOR LH

C
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
A

USE SIMULATION METHOD TO CHECK