Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1155/39    Rear Airbag Sensor LH Circuit Malfunction

for Preparation Click here


DESCRIPTION

The rear airbag sensor LH circuit consists of the center airbag sensor assembly and rear airbag sensor LH.
If the center airbag sensor assembly receives signals from the rear airbag sensor LH, it judges whether or not the SRS should be activated.
DTC B1155/39 is recorded when a malfunction is detected in the rear airbag sensor LH circuit.

DTC No.
DTC Detecting Condition
Trouble Area
B1155/39
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the rear airbag sensor LH circuit for 2 seconds.
  2. Rear airbag sensor LH malfunction
  3. Center airbag sensor assembly malfunction
  1. Rear airbag sensor LH
  2. Center airbag sensor assembly
  3. Floor wire

WIRING DIAGRAM


H043054E16


INSPECTION PROCEDURE

1.CHECK DTC


    C111663E01
  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1155/39 is not output.

    HINT:
    Codes other than code B1155/39 may be output at this time, but they are not related to this check.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK 

2.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the rear airbag sensor LH.

    OK:
    The connectors are connected.



NG
CONNECT CONNECTORS
OK


3.CHECK FLOOR WIRE (OPEN)


    C111715E07
  1. Disconnect the connectors from the center airbag sensor assembly and the rear airbag sensor LH.

  1. Using a service wire, connect A20-14 (VUCL) and A20-13 (ESCL) of connector "B".

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    S16-4 (VUCL) -
    S16-1 (ESCL)
    Always
    Below 1 Ω



    C111716E07
  1. Using a service wire, connect A20-15 (CSL+) and A20-1 (CSL-) of connector "B".

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    S16-3 (CSL+) - S16-2 (CSL-)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE FLOOR WIRE
OK


4.CHECK FLOOR WIRE (SHORT TO B+)


    C109483E06
  1. Disconnect SST from connector "B".

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester connection
    Condition
    Specified condition
    S16-4 (VUCL) - Body ground
    Ignition switch ON
    Below 1 V
    S16-1 (ESCL) - Body ground
    Ignition switch ON
    Below 1 V
    S16-3 (CSL+) - Body ground
    Ignition switch ON
    Below 1 V
    S16-2 (CSL-) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE FLOOR WIRE
OK


5.CHECK FLOOR WIRE (SHORT TO GROUND)


    C109483E07
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    S16-4 (VUCL) - Body ground
    Always
    1 MΩ or higher
    S16-1 (ESCL) - Body ground
    Always
    1 MΩ or higher
    S16-3 (CSL+) - Body ground
    Always
    1 MΩ or higher
    S16-2 (CSL-) - Body ground
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK


6.CHECK FLOOR WIRE (SHORT)


    C109483E07
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    S16-4 (VUCL) - S16-1 (ESCL)
    Always
    1 MΩ or Higher
    S16-3 (CSL+) - S16-2 (CSL-)
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK


7.CHECK REAR AIRBAG SENSOR LH


    C157639E01
  1. Connect the connector to the center airbag sensor assembly.

  1. Interchange the rear airbag sensor RH with LH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1154/38 and B1155/39 are not output.
    A
    DTC B1154/38 is output.
    B
    DTC B1155/39 is output.
    C

    HINT:
    Codes other than DTC B1154/38 and B1155/39 may be output at this time, but they are not related to this check.



B
REPLACE REAR AIRBAG SENSOR LH

C
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
A

USE SIMULATION METHOD TO CHECK