Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B0126/27    Seat Belt Buckle Switch LH Circuit Malfunction

for Preparation Click here


DESCRIPTION

The seat belt buckle switch LH circuit consists of the center airbag sensor assembly and the front seat inner belt assembly LH.
DTC B0126/27 is recorded when a malfunction is detected in the seat belt buckle switch LH circuit.

DTC No.
DTC Detecting Condition
Trouble Area
B0126/27
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the seat belt buckle switch LH circuit for 2 seconds.
  2. Front seat inner belt assembly LH malfunction
  3. Center airbag sensor assembly malfunction
  1. Front seat inner belt assembly LH (Seat belt buckle switch LH)
  2. Center airbag sensor assembly
  3. Floor wire

WIRING DIAGRAM


C171059E02


INSPECTION PROCEDURE

1.CHECK DTC


    C110423E01
  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B0126/27 is not output.

    HINT:
    Codes other than code B0126/27 may be output at this time, but they are not related to this check.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK 

2.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the front seat inner belt assembly LH.

    OK:
    The connectors are connected.



NG
CONNECT CONNECTORS
OK


3.CHECK VEHICLE
  1. Check the front driver seat type.

    Result:

    Result
    Proceed to
    w/ Power seat
    A
    w/o Power seat
    B



B
Go to step 11
A


4.CHECK FLOOR WIRE (OPEN)


    C171058E01
  1. Disconnect the connectors from the center airbag sensor assembly and the front seat inner belt assembly LH.

  1. Using a service wire, connect A20-19 (LBE+) and A20-2 (LBE-) of connector "B".

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    B18-4 (LBE+) - B18-6 (LBE-)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE FLOOR WIRE
OK


5.CHECK FLOOR WIRE (SHORT TO B+)


    C123666E01
  1. Disconnect the service wire from connector "B".

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester connection
    Condition
    Specified condition
    B18-4 (LBE+) -
    Body ground
    Ignition switch ON
    Below 1 V
    B18-6 (LBE-) -
    Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE FLOOR WIRE
OK


6.CHECK FLOOR WIRE (SHORT TO GROUND)


    C123666E03
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    B18-4 (LBE+) -
    Body ground
    Always
    1 MΩ or higher
    B18-6 (LBE-) -
    Body ground
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK


7.CHECK FLOOR WIRE (SHORT)


    C123666E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    B18-4 (LBE+) - B18-6 (LBE-)
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK


8.CHECK FRONT SEAT INNER BELT ASSEMBLY LH


    C110423E03
  1. Connect the connectors to the front seat inner belt assembly LH and the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B0126/27 is not output.

    HINT:
    Codes other than code B0126/27 may be output at this time, but they are not related to this check.



NG
Go to step 9
OK

USE SIMULATION METHOD TO CHECK 

9.REPLACE FRONT SEAT INNER BELT ASSEMBLY LH
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the front seat inner belt assembly LH (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle if possible.


NEXT


10.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    C110423E04
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B0126/27 is output.

    HINT:
    Codes other than code B0126/27 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK

END 

11.CHECK FLOOR WIRE (OPEN)


    C110424E07
  1. Disconnect the connectors from the center airbag sensor assembly and the front seat inner belt assembly LH.

  1. Using a service wire, connect A20-19 (LBE+) and A20-2 (LBE-) of connector "B".

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    B18-1 (LBE+) - B18-3 (LBE-)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE FLOOR WIRE
OK


12.CHECK FLOOR WIRE (SHORT TO B+)


    C111660E08
  1. Disconnect the service wire from connector "B".

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester connection
    Condition
    Specified condition
    B18-1 (LBE+) - Body ground
    Ignition switch ON
    Below 1 V
    B18-3 (LBE-) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE FLOOR WIRE
OK


13.CHECK FLOOR WIRE (SHORT TO GROUND)


    C111660E08
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    B18-1 (LBE+) - Body ground
    Always
    1 MΩ or higher
    B18-3 (LBE-) - Body ground
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK


14.CHECK FLOOR WIRE (SHORT)


    C111660E08
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    B18-1 (LBE+) - B18-3 (LBE-)
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK


15.CHECK FRONT SEAT INNER BELT ASSEMBLY LH


    C110423E01
  1. Connect the connectors to the front seat inner belt assembly LH and the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B0126/27 is not output.

    HINT:
    Codes other than code B0126/27 may be output at this time, but they are not related to this check.



NG
Go to step 16
OK

USE SIMULATION METHOD TO CHECK 

16.REPLACE FRONT SEAT INNER BELT ASSEMBLY LH
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the front seat inner belt assembly LH (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle if possible.


NEXT


17.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    C110423E01
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B0126/27 is not output.

    HINT:
    Codes other than code B0126/27 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK

END