Home › BODY ELECTRICAL › AUDIO / VISUAL › AUDIO AND VISUAL SYSTEM

AUDIO AND VISUAL SYSTEM > Steering Pad Switch Circuit

for Preparation Click here


DESCRIPTION

This circuit sends an operation signal from the steering pad switch to the radio receiver.
If there is an open in the circuit, the audio system cannot be operated using the steering pad switch.
If there is a short in the circuit, the same condition as that when the switch is continuously depressed occurs.
Therefore, the radio receiver cannot be operated using the steering pad switch, and also the radio receiver itself cannot function.

WIRING DIAGRAM


E155780E01


INSPECTION PROCEDURE

NOTICE:
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the Supplemental Restraint System (Click here).

1.INSPECT RADIO RECEIVER


    E120024E01
  1. Disconnect the radio receiver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    SW1 - SWG
    No switch is pushed
    Approx. 100 kΩ
    SW1 - SWG
    SEEK+ switch: push
    Approx. 0 Ω
    SW1 - SWG
    SEEK- switch: push
    Approx. 0.3 kΩ
    SW1 - SWG
    VOL+ switch: push
    Approx. 1 kΩ
    SW1 - SWG
    VOL- switch: push
    Approx. 3.2 kΩ
    SW2 - SWG
    No switch is pushed
    Approx. 100 kΩ
    SW2 - SWG
    MODE switch: push
    Approx. 0 Ω
    SW2 - SWG (*1)
    VOICE switch: push
    Approx. 3.2 kΩ
    SW2 - SWG (*1)
    ON HOOK switch: push
    Approx. 0.3 kΩ
    SW2 - SWG (*1)
    OFF HOOK switch: push
    Approx. 1 kΩ

    *1: 10 Speaker System
    *2: 6 Speaker with Rear Seat Entertainment System
    *3: 6 Speaker without Rear Seat Entertainment System



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE 

2.INSPECT STEERING PAD SWITCH ASSEMBLY


  1. Disconnect the steering pad switch assembly connector.


    E120112E03

  1. Measure the resistance according to the values in the table below.

    Standard resistance:

    Tester connection
    Condition
    Specified condition
    AU1 - EAU
    No switch is pushed
    Approx. 100 kΩ
    AU1 - EAU
    SEEK+ switch: push
    Approx. 0 Ω
    AU1 - EAU
    SEEK- switch: push
    Approx. 0.3 kΩ
    AU1 - EAU
    VOL+ switch: push
    Approx. 1 kΩ
    AU1 - EAU
    VOL- switch: push
    Approx. 3.2 kΩ
    AU2 - EAU
    No switch is pushed
    Approx. 100 kΩ
    AU2 - EAU
    MODE switch: push
    Approx. 0 Ω
    AU2 - EAU (*1)
    VOICE switch: push
    Approx. 3.2 kΩ
    AU2 - EAU (*1)
    ON HOOK switch: push
    Approx. 0.3 kΩ
    AU2 - EAU (*1)
    OFF HOOK switch: push
    Approx. 1 kΩ

    *1: 10 Speaker System



NG
REPLACE STEERING PAD SWITCH ASSEMBLY
OK


3.INSPECT SPIRAL CABLE


    E113447E17
  1. Disconnect the spiral cable connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Spiral Cable Position
    Specified condition
    EAU - EAU
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    AU1 - AU1
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    AU2 - AU2
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right

    NOTICE:
    The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the page shown in the brackets (Click here).



NG
REPLACE SPIRAL CABLE
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE - RADIO RECEIVER)