Home › BODY ELECTRICAL › METER › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > Speedometer Malfunction

for Preparation Click here


DESCRIPTION

Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart .

WIRING DIAGRAM


E118057E05


INSPECTION PROCEDURE

NOTICE:
If the vehicle speed is outside the allowable range when tested, perform the following procedure .

1.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Connect Techstream to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Turn the tester ON.

  1. Enter the following menus: Body Electrical / Main Body / Active Test.

  1. Check the operation by referring to the values in the table below.

    Combination Meter: 
    Tester Display
    Measurement Item/Range
    Test Details
    Diagnostic Note
    Speedometer Operation
    Speedometer
    0, 40, 80, 120 (mph) (*1)
    -
    0, 40, 80, 120, 160 (km/h) (*2)
    -
    *1: for U.S.A.
    *2: Except for U.S.A.

    OK:
    Needle indication is within the allowable range.



NG
REPLACE COMBINATION METER ASSEMBLY
OK


2.READ VALUE USING TECHSTREAM
  1. Connect Techstream to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Turn the tester ON.

  1. Enter the following menus: Body Electrical / Combination Meter / Data List.

  1. Check the values by referring to the values in the table below.

    Combination Meter: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed Meter
    Vehicle speed/Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
    Almost same as actual speed (When driving)
    -

    OK:
    Vehicle speed displayed on the tester is almost the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



NG
Go to step 3
OK

REPLACE COMBINATION METER ASSEMBLY 

3.READ VALUE USING TECHSTREAM
  1. Connect Techstream to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Turn the tester ON.

  1. Enter the following menus: Chassis / ABS/TRAC/VSC / Data List.

  1. Check the values by referring to the values in the table below.

    ABS/TRAC/VSC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    (FL/FR/RL/RR) Wheel Speed
    Vehicle speed/Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Almost same as actual speed (When driving)
    -

    OK:
    Vehicle speed displayed on the tester is almost the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



NG
GO TO BRAKE CONTROL SYSTEM
OK


4.INSPECT COMBINATION METER ASSEMBLY


    E123270E02
  1. Disconnect the S3 connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    S3-17 (SP1) (*1) - Body ground
    Turn the ignition switch to the ON position.
    10 to 14 V
    S3-12 (SP1) (*2) - Body ground
    Turn the ignition switch to the ON position.
    10 to 14 V

    *1: without VSC
    *2: with VSC

    Result:
    Result
    Proceed to
    OK
    A
    NG (without VSC)
    B
    NG (with VSC)
    C



B
Go to step 6

C
Go to step 7
A


5.INSPECT COMBINATION METER ASSEMBLY


    E123271E01
  1. Check the input signal waveform.

    1. Remove the combination meter assembly with connector(s) still connected.

    2. Connect the oscilloscope to terminal C10-35 (SI) and body ground.

    3. Turn the wheel slowly.

    4. Check the signal waveform according to the condition(s) in the table below.
      Item
      Condition
      Tool setting
      5 V/DIV., 20 ms./DIV.
      Vehicle condition
      Driving at approx. 20 km/h (12 mph)

      OK:
      The waveform is displayed as shown in the illustration.

      HINT:
      As the vehicle speed increases, the cycle of the signal waveform narrows.

      Result:
      Result
      Proceed to
      OK
      A
      NG (without VSC)
      B
      NG (with VSC)
      C



B
REPLACE BRAKE ACTUATOR ASSEMBLY

C
REPLACE ABS & TRACTION ACTUATOR ASSEMBLY
A

REPLACE COMBINATION METER ASSEMBLY 

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BRAKE ACTUATOR ASSEMBLY)


    E123272E01
  1. Disconnect the S3 and C10 connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S3-17 (SP1) - C10-35 (SI)
    Always
    Below 1 Ω
    S3-17 (SP1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY 

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ABS & TRACTION ACTUATOR ASSEMBLY)


    E123273E01
  1. Disconnect the S3 and C10 connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S3-12 (SP1) - C10-35 (SI)
    Always
    Below 1 Ω
    S3-12 (SP1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY