CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY > INSTALLATION |
| 1. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Bank 2 Exhaust Side) |
![]() |
Apply a light coat of engine oil to the new O-ring and install it to the camshaft timing oil control valve.
![]() |
Install the camshaft timing oil control valve assembly with the bolt.
Connect the camshaft timing oil control valve assembly connector.
| 2. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Bank 2 Intake Side) |
![]() |
Apply a light coat of engine oil to the new O-ring and install it to the camshaft timing oil control valve.
![]() |
Install the camshaft timing oil control valve assembly with the bolt.
| 3. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Bank 1 Exhaust Side) |
![]() |
Apply a light coat of engine oil to the new O-ring and install it to the camshaft timing oil control valve.
![]() |
Install the camshaft timing oil control valve assembly with the bolt.
Connect the camshaft timing oil control valve assembly connector.
| 4. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Bank 1 Intake Side) |
![]() |
Apply a light coat of engine oil to the new O-ring and install it to the camshaft timing oil control valve.
![]() |
Install the camshaft timing oil control valve assembly with the bolt.
Connect the camshaft timing oil control valve assembly connector.
| 5. INSTALL INTAKE AIR SURGE TANK ASSEMBLY |
| Oil Application Prohibited Bolt |
| Bolt for surge tank and intake manifold |
| Bolt for No. 1 surge tank stay and surge tank |
| Bolt for throttle body bracket and surge tank |
![]() |
Install a new gasket to the intake air surge tank [A].
Using a 5 mm hexagon socket wrench, install the 4 bolts [B].
Install the intake air surge tank with the 2 nuts and 2 bolts [C].
![]() |
Connect the connector [D].
![]() |
Connect the union to check valve hose [E].
Connect the ventilation hose No. 2 [F].
![]() |
Install the clamp and connect the throttle with motor body assembly connector [G].
Connect the vapor feed hose [H].
Connect the 2 water by-pass hoses to the throttle with motor body assembly [I].
| 6. INSTALL AIR CLEANER CASE SUB-ASSEMBLY |
![]() |
Install the air cleaner case with the 3 bolts.
Connect the vacuum hose.
Connect the vacuum switching valve connector.
| 7. INSTALL AIR CLEANER CAP SUB-ASSEMBLY |
![]() |
Install the air cleaner cap sub-assembly with the 2 bolts.
![]() |
Connect the the vacuum hose (EVAP) to the air cleaner hose.
Install the No. 2 ventilation hose and air cleaner hose band.
![]() |
Connect the 3 vacuum hoses.
| 8. INSTALL NO. 1 AIR CLEANER INLET |
![]() |
Install the No. 1 air cleaner inlet with the bolt.
| 9. INSTALL NO. 2 AIR CLEANER INLET |
![]() |
Install the No. 2 air cleaner inlet with the 2 clamps and 2 bolts.
| 10. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
Tighten the 2 cylinder block drain cock plugs.
Remove the air drain cock plug from the water inlet housing.
![]() |
Loosen the air drain plug at the top of the radiator 3 or 4 turns.
Add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the engine air drain cock hole. Then install the air drain cock plug to the water inlet housing.
Continue to add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the radiator air drain hole. Then close the air drain plug at the top of the radiator.
Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).
Slowly pour coolant into the radiator reservoir tank until it reaches the FULL line.
Squeeze the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level is low, add coolant.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2500 to 3000 rpm.
Squeeze the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine and wait until the engine coolant cools down.
Add engine coolant to the FULL line on the radiator reservoir.
| 11. INSPECT FOR ENGINE COOLANT LEAK |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.
| 12. INSPECT FOR ENGINE OIL LEAK |
Start the engine. Check for engine oil leaks from the connected parts of the oil filter cap and oil filter drain plug.
| 13. INSTALL V-BANK COVER SUB-ASSEMBLY |
![]() |
Fit the 3 retainers and install the V-bank cover.
| 14. INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY |
![]() |
Install the front outer cowl top panel sub-assembly with the 7 bolts.
![]() |
Install the 2 clips.
Install the fuel pump resistor with the nut.
| 15. INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY |