DTC P0741 Torque Converter Clutch Solenoid Performance (Shift Solenoid Valve DSL) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0741 | Lock-up does not occur when driving in the lock-up range (normal driving at 80 km/h [50 mph]), or lock up remains ON in the lock-up OFF range. (2-trip detection logic) |
|
| Related DTCs | P0741: Shift solenoid valve DSL/OFF malfunction Shift solenoid valve DSL/ON malfunction |
| Required sensors/Components | Shift solenoid valve DSL, Speed sensor (NT), Speed sensor (NC), Crankshaft position sensor (NE), Throttle position sensor (VPA1), Mass air flow sensor (MAF), Transmission temperature sensor (THO1), Engine coolant temperature sensor (ECT) |
| Frequency of operation | Continuous |
| Duration | OFF malfunction (A) Continuous. OFF malfunction (B) 1 sec. OFF malfunction (C) 3.5 sec. ON malfunction 1.8 sec. |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever this DTC is not present. | P0115 - P0118 (ECT sensor) P0125 (Insufficient ECT for closed loop) P0500 (VSS) P0748, P0778, P0798 (Shift solenoid valve (range)) |
| ECT (Engine coolant temperature) | 10°C (50°F) or more |
| Transmission range | "D" |
| TFT (Transmission fluid temperature) | -20°C (-4°F) or more |
| TFT sensor circuit | Not circuit malfunction |
| ECT sensor circuit | Not circuit malfunction |
| Turbine speed sensor circuit | Not circuit malfunction |
| Intermediate shaft speed sensor circuit | Not circuit malfunction |
| Output speed sensor circuit | Not circuit malfunction |
| Shift solenoid valve SL1 circuit | Not circuit malfunction |
| Shift solenoid valve SL2 circuit | Not circuit malfunction |
| Shift solenoid valve SL3 circuit | Not circuit malfunction |
| Shift solenoid valve S4 circuit | Not circuit malfunction |
| Shift solenoid valve SR circuit | Not circuit malfunction |
| Shift solenoid valve DSL circuit | Not circuit malfunction |
| Electronic throttle system | Not circuit malfunction |
| ECM selected gear | 3rd |
| Throttle valve opening angle | 4.5% or more at engine speed gear 1,900 rpm (varies with engine speed) |
| ECM selected gear | 5th |
| Vehicle speed | 10 km/h (6.2 mph) or more |
| ECM lock-up command | ON |
| ECM selected gear | 3rd, 4th or 5th |
| Vehicle speed | 25 km/h (15.5 mph) or more |
| ECM lock-up command | OFF |
| ECM selected gear | 3rd, 4th or 5th |
| Throttle valve opening angle | 7% or more |
| Vehicle speed | 25 to 60 km/h (15.5 to 37.3 mph) |
| Engine Speed - Input (turbine) speed | 100 rpm or more |
| Difference between engine speed and input (turbine) speed | Less than 35 rpm |
| PERFORM ACTIVE TEST |
Warm up the engine.
Turn the ignition switch off.
Connect Techstream to the DLC3.
Turn the ignition switch to the ON position.
Turn on the tester.
Select the item "Powertrain / Engine and ECT / Active Test".
According to the display on the tester, perform the "Active Test".
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Activate the Lock Up | [Test Details] Control the shift solenoid DSL to set the automatic transaxle to the lock-up condition. [Vehicle Condition]
| ON/OFF | Possible to check the DSL operation. |
Lightly depress the accelerator pedal and check that the engine speed does not change abruptly.

| 1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P0741) |
Connect Techstream to the DLC3.
Turn the ignition switch to the ON position and turn the Techstream main switch ON.
When you use Techstream:
Select the item "Powertrain / Engine and ECT / Trouble Codes".
Read the DTCs using Techstream.
| Result | Proceed to |
| P0741 | A |
| P0741 and other DTCs | B |
|
| ||||
| A | |
| 2.INSPECT TRANSMISSION WIRE (DSL) |
![]() |
Disconnect the transmission wire connector from the transaxle.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition 20°C (68°F) |
| 10 (DSL) - Body ground | 11 to 13 Ω |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM) |
![]() |
Connect the transmission wire connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition 20°C (68°F) |
| E10-11 (DSL) - Body ground | 11 to 13 Ω |
|
| ||||
| OK | |
| 4.INSPECT SHIFT SOLENOID VALVE DSL |
![]() |
Remove the shift solenoid valve DSL.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition 20°C (68°F) |
| Solenoid Connector (DSL) - Solenoid Body (DSL) | 11 to 13 Ω |
Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body.
|
| ||||
| OK | |
| 5.CHECK TRANSMISSION WIRE |
|
| ||||
| OK | |
| 6.INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
|
| ||||
| OK | |
| 7.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY |
|
| ||||
| OK | ||
| ||