Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM (w/ Jam Protection Function)

POWER WINDOW CONTROL SYSTEM (w/ Jam Protection Function) > OPERATION CHECK

for Preparation Click here



CHECK WINDOW LOCK SWITCH
B066761
  1. Check that the passenger side power window and slide door power window operation is disabled when the window lock switch of the power window master switch is pressed.

  2. Check that the passenger side power window and slide door power windows can be operated when the window lock switch is pressed again.


CHECK MANUAL UP/DOWN FUNCTION
  1. Check that the driver side power window can be operated using the AUTO (driver side) switch of the power window master switch as follows:

    Standard:

    Condition
    Master Switch
    Switch Operation
    Power Window
    Ignition switch ON
    AUTO (driver side)
    Pull halfway up
    UP (Closed)
    Push halfway down
    DOWN (Open)

  2. Check that the passenger power window and slide door power windows can be operated using each power window regulator switch as follows:

    Standard:

    Condition
    Master Switch
    Switch Operation
    Power Window
    1. Ignition switch ON
    2. Window lock switch OFF
    Passenger side
    Pull up
    UP (Closed)
    Push down
    DOWN (Open)
    Rear LH
    Pull up
    UP (Closed)
    Push down
    DOWN (Open)
    Rear RH
    Pull up
    UP (Closed)
    Push down
    DOWN (Open)


CHECK AUTO UP/DOWN FUNCTION
  1. Check that the driver side power window can be operated using the AUTO (driver side) switch of the power window master switch as follows:

    Standard:

    Condition
    Master Switch
    Switch Operation
    Power Window
    Ignition switch ON
    AUTO (driver side)
    Pull halfway up
    AUTO UP (Fully closed)
    Push halfway down
    AUTO DOWN (Fully open)


CHECK REMOTE MANUAL UP/DOWN FUNCTION
  1. Check that the passenger side power window and slide door power window can be operated using each switch of the power window master switch as follows:

    Standard:

    Condition
    Master Switch
    Switch Operation
    Power Window
    1. Ignition switch ON
    2. Window lock switch OFF
    Passenger side
    Pull up
    UP (Closed)
    Push down
    DOWN (Open)
    Rear LH
    Pull up
    UP (Closed)
    Push down
    DOWN (Open)
    Rear RH
    Pull up
    UP (Closed)
    Push down
    DOWN (Open)


CHECK MANUAL DOWN FUNCTION VIA TRANSMITTER
  1. Check that all power windows and sliding roof (standard type only) operate as follows when operating the transmitter:

    Standard:

    Condition
    Transmitter Operation
    Position/Operation
    1. No key in ignition key cylinder
    2. Any door UNLOCK
    Press UNLOCK switch pressed for 1.5 sec. or more
    All power windows go DOWN
    1. No key in ignition key cylinder
    2. All doors CLOSE
    3. All doors LOCK
    Press LOCK switch pressed for 1.5 sec. or more
    All power windows go UP

    HINT:
    For a sign for starting operation, the wireless door lock buzzer sounds once (answer-back).


CHECK POWER WINDOW OPERATION FUNCTION AFTER IGNITION SWITCH IS TURNED OFF
  1. When both of the following conditions are fulfilled, check that the power windows can be operated even after the ignition switch is turned off.

    1. Within 45 seconds after the ignition switch is turned off.

    2. The front doors are closed.


CHECK JAM PROTECTION FUNCTION
B051853E01

HINT:
The jam protection function prevents any part of your body from getting caught by accident between the door frame and the door glass during power window operation.

NOTICE:
If the power window motor has been reset, raise and lower the door glass several times using MANUAL function before performing the check.

  1. Check that the door glass goes down by approx. 50 mm (1.97 in.) right when something gets caught between the door frame and door glass during power window operation. However, when the opening between the door frame and the door glass is less than 200 mm (7.87 in.), the door glass keeps going down until the operation reaches 200 mm (7.87 in.) and stops there.

    1. AUTO UP
    2. AUTO UP operation after the ignition switch OFF
    3. MANUAL UP operation after the ignition switch OFF


CHECK POWER WINDOW FAIL-SAFE FUNCTION
  1. If there is a malfunction in the pulse sensor of the power window motor, the power window function will be restricted to partial operation.

    Power Window Function
    (Switch Operation)
    Ignition Switch ON
    Ignition Switch OFF
    Manual UP
    (Pull halfway up)
    Disabled *
    Disabled
    Manual DOWN
    (Push halfway down)
    Operative
    Disabled
    AUTO UP
    (Pull fully up)
    Disabled
    Disabled
    AUTO DOWN
    (Push fully down)
    Disabled
    Disabled
    *: However, manual UP function of the power window is operative when fully pulling up the power window switch.