Home › TRANSMISSION ยท U151E AUTOMATIC TRANSAXLE › VALVE BODY ASSEMBLY

VALVE BODY ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL TRANSMISSION VALVE BODY ASSEMBLY


    C089115
  1. Install the shift solenoid valve SL1 to the valve body assembly with the bolt.

    Torque:
    6.6 N*m{ 67 kgf*cm , 58 in.*lbf }



    C089113
  1. Install the shift solenoid valve SL2 to the valve body assembly with the bolt.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }



    D026443
  1. Install the shift solenoid valve DSL to the valve body assembly with the bolt.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }



    D026438
  1. Install the shift solenoid valve SR to the valve body assembly.



    D026442
  1. Install the shift solenoid valve S4 to the valve body assembly with the bolt.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }



    C089112
  1. Install the shift solenoid valve SL3 and SLT to the valve body assembly.

  1. Install the lock plate to the valve body assembly with the bolt.

    Torque:
    6.6 N*m{ 67 kgf*cm , 58 in.*lbf }



    C050017
  1. Install the spring and check ball body.



    C091933E05
  1. Align the groove of the manual valve with the pin of the lever.

  1. Install the 17 bolts.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

    NOTICE:
    1. Push the valve body against the accumulator piston springs and check ball body to install the valve body.
    2. First, temporarily tighten the bolts marked with (1) in the illustration because they are positioning bolts.

    Bolt length:
    Bolt A:
    41 mm (1.614 in.)
    Bolt B:
    57 mm (2.244 in.)
    Bolt C:
    25 mm (0.984 in.)



2. INSTALL VALVE BODY OIL STRAINER ASSEMBLY


    C091932
  1. Coat a new O-ring with ATF.

  1. Install the O-ring to the oil strainer.



    C091931
  1. Install the oil strainer with the 3 bolts.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }



3. INSTALL TRANSMISSION WIRE


    C091927E04
  1. Coat the O-ring with ATF.

  1. Install the ATF temperature sensor with the lock plate and bolt.

    Torque:
    6.6 N*m{ 67 kgf*cm , 58 in.*lbf }

  1. Connect the 7 shift solenoid valve connectors.



4. INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY


    D030865
  1. Install the 2 magnets in the oil pan.

  1. Apply seal packing or equivalent to the 18 bolts.

    Seal packing:
    THREE BOND 2430 or equivalent



    C091925
  1. Install the oil pan and new gasket with the 18 bolts to the transaxle case.

    Torque:
    7.8 N*m{ 80 kgf*cm , 69 in.*lbf }

    NOTICE:
    Tighten the bolts within 10 minutes of sealant application.



5. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


6. ADD AUTOMATIC TRANSAXLE FLUID


7. CHECK FLUID LEVEL IN AUTOMATIC TRANSAXLE

HINT:
Drive the vehicle so that the engine and transaxle are at normal operating temperature.

Fluid temperature:
70 to 80°C (158 to 176°F)

  1. Park the vehicle on a level surface and set the parking brake.



    D025120E05
  1. With the engine idling and the brake pedal depressed, move the shift lever to all positions from P to L and return to the P position.

  1. Take out the dipstick and wipe it clean.

  1. Put the dipstick back all the way.

  1. Take out the dipstick again and check that the fluid level is within the HOT range.
    If the fluid level is below the HOT range, add new fluid and recheck the fluid level.
    If the fluid level exceeds the HOT range, drain the fluid once, add the proper amount of new fluid and recheck the fluid level.
    If there are leaks, it is necessary to repair or replace O-rings, FIPGs, oil seals, plugs and/or other parts.



8. INSTALL ENGINE UNDER COVER NO.1


9. RESET MEMORY

HINT:
(Click here)