Home › TRANSMISSION ยท U151E AUTOMATIC TRANSAXLE › DIFFERENTIAL CASE

DIFFERENTIAL CASE > REASSEMBLY

for Preparation Click here



1. INSTALL FRONT DIFFERENTIAL SIDE GEAR


    C050242E01
  1. Apply ATF to the 2 front differential side gears, 2 side gear thrust washers, 2 front differential pinions and 2 pinion thrust washers and install them to the differential case.



2. INSTALL FRONT DIFFERENTIAL PINION SHAFT NO.1


    C050241E01
  1. Coat the front differential pinion shaft No.1 with ATF, and install it to the differential case.



3. INSPECT BACKLASH

HINT:



4. INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN


    C050253
  1. Using a pin punch and a hammer, install the pinion shaft straight pin.



    C050254
  1. Using a chisel and a hammer, stake the differential case.

    NOTICE:
    Stake the differential case after adjusting the backlash.



5. INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING


    D026447E01
  1. Using SST and a press, install the front differential case front tapered roller bearing to the differential case.

    SST
    09316-12010  
    09550-60010   (09951-00490)
    09950-70010   (09951-07100)

    NOTICE:
    Do not damage the bearing cage when installing the bearing inner race.



    C083736
  1. Using SST and a hammer, install the front differential case tapered roller bearing front outer race to the transaxle housing.

    SST
    09550-60010   (09951-00490)
    09950-60020   (09951-00910)



6. INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING


    D026448E02
  1. Using SST and a press, install the front differential case front tapered roller bearing to the differential case.

    SST
    09316-12010  
    09550-60010   (09951-00490)
    09950-70010   (09951-07100, 09951-07150)

    NOTICE:
    Do not damage the bearing cage when installing the bearing inner race.



    D026449E01
  1. Using SST and a hammer, install the front differential case tapered roller bearing rear outer race to the transaxle housing.

    SST
    09950-70010   (09951-07100, 09951-07150)
    09950-60020   (09951-00890)

    NOTICE:
    No clearance is allowed between the bearing and transaxle housing.



7. ADJUST DIFFERENTIAL SIDE BEARING PRELOAD


    D026450E01
  1. Install the differential assembly to the transaxle case.



    D026384E02
  1. Clean the mating surfaces of the transaxle case and transaxle housing.

  1. Install the transaxle housing to the transaxle case and tighten them with the 16 bolts.

    Torque:
    Bolt A:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }
    Bolt B:
    33 N*m{ 337 kgf*cm , 24 ft.*lbf }
    Bolt C:
    29 N*m{ 295 kgf*cm , 21 ft.*lbf }
    Bolt D:
    22 N*m{ 226 kgf*cm , 16.0 ft.*lbf }

    HINT:
    Apply seal packing or equivalent to bolts A and D.

    Seal packing:
    THREE BOND 2403 or equivalent

    Bolt length:
    Bolt A:
    50 mm (1.969 in.)
    Bolt B:
    50 mm (1.969 in.)
    Bolt C:
    42 mm (1.654 in.)
    Bolt D:
    72 mm (2.835 in.)

    HINT:
    Usually, bolt A is non-reusable. In this case, however, the bolt can be used after cleaning it.



    D025604E01
  1. Using SST, turn the differential assembly to the right and left 2 or 3 times to settle the bearing.

    SST
    09564-32011  

  1. Using SST and a torque wrench, measure the turning torque of the differential.

    SST
    09564-32011  

    Turning torque at 60 rpm:
    New bearing:
    0.20 to 0.69 N*m (2.0 to 7.0 kgf*cm, 1.8 to 6.1 in.*lbf)
    Used bearing:
    0.10 to 0.35 N*m (1.0 to 3.6 kgf*cm, 0.9 to 3.1 in.*lbf)

    HINT:
    If the turning torque is not as specified, refer to the table below to select a thrust washer so that the specified value is achieved.

    Flange thickness: mm (in.) 
    Mark
    Thickness
    Mark
    Thickness
    0
    2.00 (0.0787)
    9
    2.45 (0.0965)
    1
    2.05 (0.0807)
    A
    2.50 (0.0984)
    2
    2.10 (0.0827)
    B
    2.55 (0.1004)
    3
    2.15 (0.0846)
    C
    2.60 (0.1024)
    4
    2.20 (0.0866)
    D
    2.65 (0.1043)
    5
    2.25 (0.0886)
    E
    2.70 (0.1063)
    6
    2.30 (0.0906)
    F
    2.75 (0.1083)
    7
    2.35 (0.0925)
    G
    2.80 (0.1102)
    8
    2.40 (0.0945)
    H
    2.85 (0.1122)



    D026384
  1. Remove the 16 bolts and the transaxle housing.



    D026450E04
  1. Remove the differential assembly.



8. INSTALL FRONT DIFFERENTIAL RING GEAR


    D025215E02
  1. Using ATF and heater, heat the front differential ring gear to 90 to 110°C (194.0 to 230.0°F).

    NOTICE:
    Do not heat the ring gear to more than 110°C (230.0°F).

  1. Clean the contact surface of the front differential case.



    D026445E04
  1. Align the matchmarks, and install the front differential ring gear case quickly.

    NOTICE:
    Do not install the bolts while the ring gear is hot.



    D026446
  1. Tighten the 14 bolts.

    Torque:
    95.0 N*m{ 970 kgf*cm , 70 ft.*lbf }

    NOTICE:
    Tighten the bolts a little at a time in a diagonal pattern.



9. INSTALL TRANSAXLE HOUSING OIL SEAL


    D026451E01
  1. Using SST and a hammer, install a new oil seal.

    SST
    09223-15020  
    09950-70010   (09951-07150)

  1. Coat the lip of oil seal with a little MP grease.

    Oil seal installation depth:
    0 +- 0.5 mm (0 +- 0.0197 in.)



10. INSTALL DIFFERENTIAL SIDE BEARING RETAINER OIL SEAL


    D025606E01
  1. Using SST and a hammer, install a new oil seal.

    SST
    09710-30050  
    09950-70010   (09951-07150)

  1. Coat the lip of the oil seal with a little MP grease.

    Oil seal installation depth:
    0 +- 0.5 mm (0 +- 0.0197 in.)