Home › TRANSMISSION ยท U151F AUTOMATIC TRANSAXLE › DIFFERENTIAL CASE

DIFFERENTIAL CASE > REASSEMBLY

for Preparation Click here



1. INSTALL DIFFERENTIAL CASE SUB-ASSEMBLY NO.2


    C050943E02
  1. Coat the front differential side gear thrust washer No.1, front differential planetary ring gear, front differential pinion No.2, front differential pinion thrust washer No.2, front differential pinion shaft holder, front differential pinion shaft and 2 differential pinion shafts with ATF, install them to the differential case No.2.



    C050217E01
  1. Using a pin punch and a hammer, install 3 straight pins.



    D025610E02
  1. Using a snap ring expander, install the pinion shaft spacer snap ring.



2. INSPECT FRONT DIFFERENTIAL

HINT:



3. INSTALL CTR DIFFERENTIAL PLANETARY GEAR ASSEMBLY


    C051252E01
  1. Install the center differential side gear, conical spring washer and center differential side gear thrust washer No.2 RH from the differential case RH.

    HINT:
    Ensure that the conical washers is installed correctly.



    C050950E01
  1. Hold the differential case RH by vice. Install the center differential pinion and pinion thrust washer to the differential spider and install them to the differential case RH.

    NOTICE:
    When holding the differential case RH by vise, be sure to place an aluminum sheet between them and use a minimum force



    C050205E01
  1. Pressing and holding the differential spider toward the differential case RH, measure the pinion's backlash with a dial indicator as illustrated.

    Standard backlash:
    0.05 - 0.20 mm (0.0020 - 0.0079 in.)

    If the backlash is not within the specified value, refer to the table below and select a thrust washer which will ensure that the backlash is within the specified value.
    Thrust washer thickness: mm (in.) 
    Mark
    Thickness
    Mark
    Thickness
    MA
    0.80 (0.0313)
    MH
    1.15 (0.0453)
    MB
    0.85 (0.0333)
    MJ
    1.20 (0.0472)
    MC
    0.90 (0.0353)
    MK
    1.25 (0.0492)
    MD
    0.95 (0.0373)
    ML
    1.30 (0.0512)
    ME
    1.00 (0.0393)
    MM
    1.35 (0.0532)
    MF
    1.05 (0.0413)
    MN
    1.40 (0.0552)
    MG
    1.10 (0.0433)
    -
    -



    C050206E01
  1. Temporarily install the differential side gear thrust washer No.2 LH, center differential side gear conical spring washer and differential case No.2 to the differential case LH.

    HINT:
    Ensure that the conical washers is installed correctly.



    C050207E01
  1. Install the differential intermediate case to the above and fix them with 4 bolts.



    C050208E01
  1. remove the differential spider, 5 center differential pinions and 5 center differential pinion thrust washers from the differential case RH. Put them in the differential intermediate case and fix the case.



    C050209E01
  1. Pressing and holding the differential spider toward the differential intermediate case, measure the pinion's backlash with a dial indicator.

    Standard backlash:
    0.05 - 0.20 mm (0.0020 - 0.0079 in.)

    If the backlash is not within the specified value, refer to the table below and select a thrust washer which will ensure that the backlash is within the specified value.
    Thrust washer thickness: mm (in.) 
    Mark
    Thickness
    Mark
    Thickness
    MA
    0.80 (0.0313)
    MH
    1.15 (0.0453)
    MB
    0.85 (0.0333)
    MJ
    1.20 (0.0472)
    MC
    0.90 (0.0353)
    MK
    1.25 (0.0492)
    MD
    0.95 (0.0373)
    ML
    1.30 (0.0512)
    ME
    1.00 (0.0393)
    MM
    1.35 (0.0532)
    MF
    1.05 (0.0413)
    MN
    1.40 (0.0552)
    MG
    1.10 (0.0433)
    -
    -



    C050210E01
  1. Remove the 4 bolts and disconnect the differential case LH from the differential intermediate case.



    C051468E01
  1. Remove the differential case No.2 from the differential case LH.



    C051469E01
  1. Install the selected differential side gear thrust washer No.2 LH and center differential planetary gear to the differential case LH.



    C050188E02
  1. Install the differential case No.2 to the differential case LH again.



    C050193E02
  1. install the adjusted differential case RH to the intermediate case and tighten the 15 bolts using a "TORX" socket wrench(T50).

    Torque:
    63 N*m{ 642 kgf*cm , 46 ft.*lbf }

    NOTICE:
    Align the matchmarks.



4. INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING


    D025612E01
  1. Using SST and a press, install the front differential case tapered roller bearing FR to the differential case.

    SST
    09950-70010   (09951-07100)
    09649-17010  

    NOTICE:
    Do not make a damage on the bearing cage during the bearing inner race installation.



    D025603E01
  1. Using SST, install the outer race of the tapered roller bearing FR.

    SST
    09527-17011  
    09950-60020   (09951-01030)

    NOTICE:
    Clearance is not allowed between the plate washer and transaxle housing.



5. INSTALL FRONT DIFFERENTIAL SIDE GEAR


    D025613E01
  1. Using SST and a press, install the front differential case tapered roller bearing RR to the differential case.

    SST
    09316-20011  
    09214-76011  

    NOTICE:
    Do not make a damage on the bearing cage during the bearing inner race installation.

  1. Install the front differential case shim RR to the transaxle case.
    If the bearing is new, check to select a front differential case shim RR of proper thickness starting from the thinner ones. If the bearing is reused, check to select a front differential case shim RR starting from the same thickness as one installed before disassembly.



    D025601E01
  1. Using SST, install the outer race of the front differential case tapered roller bearing RR.

    SST
    09950-60020   (09951-00890)
    09950-70010   (09951-07100)

    NOTICE:
    Clearance is not allowed between the differential case shim and transaxle case.



6. ADJUST TAPERED ROLLER BEARING PRELOAD

HINT:



7. INSTALL FRONT DIFFERENTIAL RING GEAR


    D025215E02
  1. Using ATF and heater, heat the front differential ring gear to 90 to 110°C (194.0 to 230.0°F).

    NOTICE:
    Do not heat the ring gear to more than 110°C (230.0°F).

  1. Clean the contact surface of the front differential case.



    C050186E01
  1. Set the match-marks, install the front differential ring gear case quickly.

    NOTICE:
    Do not install the bolts while the ring gear is hot.



    C050232E01
  1. Temporarily install the 8 bolts as shown in the illustration.



    C050233E01
  1. Remove the 4 bolts shown in the illustration.

  1. Temporarily install the remaining 8 set bolts.

  1. Fully tighten the set bolts.

    Torque:
    95.1 N*m{ 970 kgf*cm , 70 ft.*lbf }

    NOTICE:
    Tighten the bolts a little at a time in diagonal order.



8. INSTALL DIFFERENTIAL SIDE BEARING RETAINER OIL SEAL


    D025605E01
  1. Using SST and a hammer, install a new oil seal.

    SST
    09223-15020  
    09950-70010   (09951-07100)

    Standard press in depth:
    -0.5 to 0.5 mm (-0.002 to 0.002 in.)

  1. Coat the rip of oil seal with a little MP grease.



9. INSTALL TRANSAXLE HOUSING OIL SEAL


    D003809E02
  1. Wind a vinyl tape around SST at the place 6.0 mm (0.236 in.) above from the bottom end until the thickness of the wound tape is about 5.0 mm (0.197 in.).

    SST
    09950-60020   (09951-00730)

    NOTICE:
    Remove foreign matter such as grease on the SST before winding the tape.

  1. Coat the rip of oil seal with a little MP grease.



    D025615E01
  1. Using SST, install a new oil seal.

    SST
    09950-60020   (09951-00730)
    09950-70010   (09951-07150)

    Standard press in depth:
    5.5 to 6.5 mm (0.217 to 0.256 in.)

    NOTICE:
    Stop pressing when the would vinyl tape is contact with the transaxle housing.