Part Tightened
| N*m
| kgf*cm
| ft.*lbf
|
Ignition coil assembly x Cylinder head cover sub-assembly
| 10
| 102
| 7
|
No. 1 engine hanger x Cylinder head sub-assembly RH
| 33
| 337
| 24
|
No. 2 engine hanger x Cylinder head sub-assembly LH
| 33
| 337
| 24
|
Engine mounting bracket RH x Cylinder block sub-assembly
| 54
| 551
| 40
|
No. 1 oil level gauge guide x Cylinder head sub-assembly
| 21
| 214
| 15
|
No. 2 oil level gauge guide x Cylinder block sub-assembly
| 21
| 214
| 15
|
No. 2 idler pulley sub-assembly x Timing chain cover sub-assembly
| 54
| 550
| 40
|
V-ribbed belt tensioner assembly x Cylinder block sub-assembly
| 43
| 438
| 32
|
Intake manifold x Cylinder head sub-assembly
| 21
| 214
| 15
|
Exhaust manifold sub-assembly RH x Cylinder head sub-assembly RH
| 21
| 214
| 15
|
Exhaust manifold sub-assembly LH x Cylinder head sub-assembly LH
| 21
| 214
| 15
|
Drive plate & ring gear sub-assembly x Crankshaft
| 83
| 850
| 61
|
Air cleaner case sub-assembly x Body
| 5.0
| 51
| 44 in.*lbf
|
Air cleaner case sub-assembly x Air cleaner bracket
| 5.0
| 51
| 44 in.*lbf
|
Engine coolant temperature x water by-pass joint RR
| 20
| 200
| 14
|
Engine assembly with Transaxle x Body
| A
| 85
| 867
| 63
|
B
| 32
| 329
| 24
|
No. 2 manifold stay x Exhaust manifold sub-assembly LH
| 34
| 347
| 25
|
No. 2 manifold stay x Cylinder block sub-assembly
| 34
| 347
| 25
|
No. 1 air cleaner inlet x Body
| 5.0
| 51
| 44 in.*lbf
|
No. 2 air cleaner inlet x Body
| 5.0
| 51
| 44 in.*lbf
|
Battery clamp x Body
| Bolt
| 5.5
| 56
| 49 in.*lbf
|
Nut
| 5.5
| 56
| 49 in.*lbf
|
Throttle body bracket x Intake air surge tank assembly
| 21
| 214
| 15
|
Throttle body bracket x Cylinder head cover sub-assembly RH
| 21
| 214
| 15
|
No. 1 surge tank stay x Intake air surge tank assembly
| 21
| 214
| 15
|
No. 1 surge tank stay x Cylinder head cover sub-assembly RH
| 21
| 214
| 15
|
No. 1 cowl top to cowl brace inner x Body
| 7.5
| 76
| 66 in.*lbf
|
No. 1 cowl top to cowl brace inner x Front outer cowl top panel sub-assembly
| 7.5
| 76
| 66 in.*lbf
|
Front outer cowl top panel sub-assembly x Body
| 7.5
| 76
| 66 in.*lbf
|
Fuel pump resistor x Front outer cowl top panel sub-assembly
| 7.5
| 76
| 66 in.*lbf
|
Radio setting condenser x Cylinder head cover sub-assembly RH
| 10
| 102
| 7
|
Radio setting condense x Cylinder head cover sub-assembly LH
| 10
| 102
| 7
|
Intake air resonator sub-assembly x Body
| 5.0
| 51
| 44 in.*lbf
|
Air cleaner bracket x Body
| 7.8
| 80
| 69 in.*lbf
|
No. 1 vacuum switching valve assembly x Cylinder head cover sub-assembly
| 10
| 102
| 7
|
Engine mounting bracket RR x Cylinder block sub-assembly
| 64
| 650
| 47
|
Steering intermediate shaft x Steering gear
| 35
| 360
| 26
|
Stabilizer link x Shock absorber
| 74
| 755
| 55
|
Tie rod assembly x Steering gear
| 49
| 500
| 36
|
Front speed sensor x Front axle
| 8.0
| 85
| 71 in.*lbf
|
Front axle hub nut x Front drive shaft
| 294
| 2998
| 217
|
Cooler compressor assembly x V-ribbed belt tensioner
| 25
| 250
| 18
|
Cooler compressor assembly x Discharge hose sub-assembly
| 5.4
| 55
| 48 in.*lbf
|
Cooler compressor assembly x Suction hose sub-assembly
| 5.4
| 55
| 48 in.*lbf
|
Engine mounting control bracket x No. 1 engine front mounting bracket LH
| Bolt A
| 44
| 450
| 32
|
Bolt B
| 38
| 388
| 28
|
Nut
| 23
| 235
| 17
|
Engine assembly with Transaxle x Front frame assembly
| Nut A
| 87
| 887
| 64
|
Nut B
| 95
| 969
| 70
|
Engine assembly with Transaxle x engine mounting insulator RR
| 78
| 795
| 58
|
Drive shaft bearing bracket x Cylinder block sub-assembly
| 64
| 650
| 47
|
No. 2 exhaust manifold heat insulator x Exhaust manifold sub-assembly LH
| 8.5
| 87
| 75 in.*lbf
|
Engine oil pressure switch assembly x Oil pan sub-assembly
| 21
| 214
| 15
|
No. 2 engine mounting stay RH x Intake manifold
| 21
| 214
| 15
|
No. 2 timing gear cover x Chain cover sub-assembly
| 6.0
| 61
| 53 in.*lbf
|
No. 1 engine front mounting bracket LH x Chain cover
| 54
| 551
| 40
|
Camshaft bearing cap x Camshaft housing
| 1st
| 10
| 102
| 7
|
2nd
| 16
| 163
| 12
|
Camshaft housing x Cylinder head sub-assembly
| 28
| 286
| 21
|
No. 1 chain tensioner x Cylinder head sub-assembly
| 10
| 102
| 7
|
No. 2 chain tensioner x Cylinder head sub-assembly
| 21
| 214
| 15
|
No. 3 chain tensioner x Cylinder head sub-assembly
| 21
| 214
| 15
|
Camshaft timing gear assembly x Camshaft
| 100
| 1,020
| 74
|
Camshaft timing exhaust gear assembly x Camshaft
| 100
| 1,020
| 74
|
Engine rear oil seal retainer x Cylinder block sub-assembly
| 10
| 102
| 7
|
Knock control sensor x Cylinder block sub-assembly
| 20
| 204
| 15
|
Water inlet pipe x Cylinder block sub-assembly
| 10
| 102
| 7
|
Cylinder head sub-assembly RH x Cylinder block sub-assembly
| 1st
| 36
| 367
| 27
|
2nd
| Turn 90°
| Turn 90°
| Turn 90°
|
3nd
| Turn 90°
| Turn 90°
| Turn 90°
|
Cylinder head sub-assembly LH x Cylinder block sub-assembly
| Recessed head 1st
| 36
| 367
| 27
|
2nd
| Turn 90°
| Turn 90°
| Turn 90°
|
3nd
| Turn 90°
| Turn 90°
| Turn 90°
|
14 mm (0.55 in.) head
| 30
| 306
| 22
|
No. 1 chain vibration damper x Cylinder block sub-assembly
| 23
| 230
| 17
|
No. 2 idle gear shaft x Cylinder block sub-assembly
| 60
| 612
| 44
|
Timing chain cover plate x Timing chain cover sub-assembly
| 9.1
| 93
| 81 in.*lbf
|
Timing chain cover sub-assembly x Cylinder head and block
| Areas 1: Bolt
| 21
| 214
| 15
|
Areas 2: Bolt
| 21
| 214
| 15
|
Areas 3: Bolt and Nut
| 21
| 214
| 15
|
Areas 4: Bolt A
| 43
| 438
| 32
|
Areas 4: Except Bolt A
| 21
| 214
| 15
|
Water pump assembly x Timing chain cover sub-assembly
| 9.1
| 93
| 81 in.*lbf
|
Oil pan baffle plate x Cylinder block sub-assembly
| 10
| 102
| 7
|
Oil pan stud bolt x Cylinder block and timing chain cover sub-assembly
| 10
| 102
| 7
|
Oil pan stud bolt x No. 2 oil pan sub-assembly
| 4.0
| 41
| 35 in.*lbf
|
Oil cooler stud bolt x Oil pan sub-assembly
| 10
| 102
| 7
|
Oil strainer stud bolt x Timing chain cover sub-assembly
| 4.0
| 41
| 35 in.*lbf
|
Oil strainer sub-assembly x Cylinder block and timing chain cover sub-assembly
| 10
| 102
| 7
|
Oil pan sub-assembly x Cylinder block and timing chain cover sub-assembly
| bolt A
| 10
| 102
| 7
|
except bolt A
| 21
| 214
| 15
|
No. 2 oil pan sub-assembly x Oil pan sub-assembly
| 10
| 102
| 7
|
Oil pan drain plug x No. 2 oil pan sub-assembly
| 40
| 408
| 30
|
Crankshaft pulley x Crankshaft
| 250
| 2,550
| 184
|
Cylinder head cover sub-assembly x Cylinder head sub-assembly RH
| bolt A
| 21
| 214
| 15
|
except bolt A
| 10
| 102
| 7
|
Cylinder head cover sub-assembly LH x Cylinder head sub-assembly LH
| bolt A
| 21
| 214
| 15
|
except bolt A
| 10
| 102
| 7
|
Water outlet x Cylinder head sub-assembly
| bolt
| 10
| 102
| 7
|
nut
| 10
| 103
| 7
|
Water inlet housing set nut
| 10
| 102
| 7
|
Stud bolt x Water inlet housing
| 4.0
| 41
| 35 in.*lbf
|
Water inlet set bolt and nut
| 10
| 102
| 7
|
Stud bolt x No. 1 oil cooler bracket
| 10
| 102
| 7
|
Oil cooler pipe x No. 1 oil cooler bracket
| bolt
| 21
| 214
| 16
|
nut
| 21
| 214
| 16
|
No. 1 oil cooler bracket w/ Oil cooler pipe x Oil pan sub-assembly and Cylinder block sub-assembly
| bolt
| 21
| 214
| 16
|
nut
| 21
| 214
| 16
|
No. 1 oil cooler bracket x Oil cooler assembly
| 68
| 693
| 50
|
Water by-pass hoses x Clamp
| 10
| 102
| 7
|
Oil filter cap x Oil pan sub-assembly
| 25
| 255
| 18
|
Oil filter cap x Drain plug
| 13
| 127
| 9
|
Camshaft position sensor x Cylinder head cover sub-assembly
| 10
| 102
| 7
|
Ventilation valve x Cylinder head cover sub-assembly LH
| 27
| 275
| 20
|
Oil pipe union x Cylinder block sub-assembly
| 65
| 663
| 48
|
Oil pipe union x Cylinder head cover sub-assembly
| 65
| 663
| 48
|
Oil pipe x Cylinder head sub-assembly
| 10
| 102
| 7
|
Crankshaft position sensor x Cylinder block sub-assembly
| 10
| 102
| 7
|
Camshaft timing oil control valve assembly x Cylinder head cover sub-assembly
| 10
| 102
| 7
|
Cylinder block water drain cock sub-assembly x Cylinder block sub-assembly
| 25
| 255
| 18
|
Drain cock sub-assembly x Water inlet housing
| 30
| 306
| 22
|
Water drain cock plug x Water drain cock sub-assembly
| 13
| 130
| 9
|
Drain cock plug x Drain cock assembly
| 13
| 130
| 9
|
Spark plug x Cylinder head sub-assembly
| 18
| 184
| 13
|
Stud bolt x Cylinder head sub-assembly
| For A and B bolts
| 10
| 102
| 7
|
For C bolts
| 4.0
| 41
| 35 in.*lbf
|
No. 1 straight screw plug x Cylinder head sub-assembly
| 44
| 449
| 32
|
No. 2 straight screw plug x Cylinder head sub-assembly
| 80
| 816
| 59
|
Main bearing cap x Cylinder block sub-assembly
| 16 pointed head 1st
| 61
| 622
| 45
|
2nd
| Turn 90°
| Turn 90°
| Turn 90°
|
14 mm head
| 52
| 525
| 38
|
Connecting rod cap x Connecting rod
| 1st
| 25
| 255
| 18
|
2nd
| Turn 90°
| Turn 90°
| Turn 90°
|
Stud bolt x Cylinder block sub-assembly
| bolt A
| 10
| 102
| 7
|
bolt B
| 17
| 173
| 13
|
No. 1 sub-assembly oil nozzle x Cylinder block sub-assembly
| 9.0
| 92
| 80 in.*lbf
|
Camshaft position sensor x Cylinder head cover sub-assembly
| 10
| 102
| 7
|