Home › STEERING › POWER STEERING › VANE PUMP

VANE PUMP > INSTALLATION

for Preparation Click here



1. INSTALL VANE PUMP ASSEMBLY


    C135238
  1. Temporarily install the bolt to the vane pump assembly.

  1. Install the vane pump assembly.



    C159000E01
  1. Temporarily install the bolt (B).

  1. Using SST, tighten the 2 bolts.

    SST
    09249-63010  

    Torque:
    Without SST:
    43 N*m{ 439 kgf*cm , 32 ft.*lbf }
    With SST:
    29 N*m{ 294 kgf*cm , 21 ft.*lbf }

    NOTICE:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
    2. This torque value is accurate when SST is parallel to the torque wrench.



2. CONNECT POWER STEERING FLUID PRESSURE SWITCH CONNECTOR


    C161547
  1. Connect the connector to the power steering fluid pressure switch.



3. CONNECT PRESSURE FEED TUBE ASSEMBLY
  1. Install a new gasket to the pressure feed tube assembly.



    C161548
  1. Temporarily connect the pressure feed tube assembly to the vane pump assembly with the union bolt.

  1. Fully tighten the union bolt.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

    NOTICE:
    Make sure that the stopper of the pressure feed tube assembly contacts the vane pump assembly securely as shown in the illustration.



4. CONNECT NO. 1 FLUID RESERVOIR TO PUMP HOSE


    C133183E02
  1. Connect the No. 1 fluid reservoir to pump hose to the vane pump assembly with the clip.

    NOTICE:
    1. Connect the No. 1 fluid reservoir to pump hose with the paint mark facing toward the rear of the vehicle.
    2. Push the No. 1 fluid reservoir to pump hose as far as it goes as shown in the illustration.
    3. Install the clip at the position specified in the illustration.



5. INSTALL FAN AND GENERATOR V BELT


    A162386E01
  1. Install the V-ribbed belt.

  1. Using SST, turn the belt tensioner counterclockwise and remove the bar.

    SST
    09249-63010  



    A129623E02
  1. If it is difficult to install the V-ribbed belt, perform the following procedure:

    1. Put the V-ribbed belt on every pulley except the tensioner pulley as shown in the illustration.

    2. While releasing the belt tension by turning the belt tensioner counterclockwise, put the V-ribbed belt on the tensioner pulley.

      NOTICE:
      1. Put the backside of the V-ribbed belt on the tensioner pulley and idler pulley.
      2. Check that the V-ribbed belt is properly set to each pulley.

    3. After installing the V-ribbed belt, check that it fits properly in the ribbed grooves. Confirm that the belt has not slipped out of the grooves on the bottom of the crank pulley by hand.



6. ADD POWER STEERING FLUID


7. BLEED POWER STEERING SYSTEM
  1. Check the fluid level .

  1. Jack up the front of the vehicle and support it with stands.

  1. Turn the steering wheel.

    1. With the engine stopped, turn the steering wheel slowly from lock to lock several times.

  1. Lower the vehicle.

  1. Start the engine.

    1. Run the engine at idle for a few minutes.

  1. Turn the steering wheel.

    1. With the engine idling, turn the steering wheel left or right to the full lock position and keep it in that position for 2 to 3 seconds, then turn the steering wheel to the opposite full lock position and keep it there for 2 to 3 seconds.

    2. Repeat this procedure several times.

  1. Stop the engine.



    C137876E01
  1. Check for foaming or emulsification.

    HINT:
    If the system has to be bled twice because of forming or emulsification, be sure to check for fluid leaks in the system.

  1. Check the fluid level .



8. CHECK POWER STEERING FLUID LEVEL
  1. Keep the vehicle level.



    C133502E01
  1. With the engine stopped, check the fluid level in the fluid reservoir.
    If necessary, add fluid.

    Fluid:
    ATF DEXRON II or III, or equivalent

    HINT:
    If the fluid is hot, check that the fluid level is within the HOT range on the fluid reservoir. If the fluid is cold, check that the fluid level is within the COLD range.

  1. Start the engine and run it at idle.

  1. Turn the steering wheel from lock to lock several times to raise fluid temperature.

    Fluid temperature:
    75 to 80°C (167 to 176°F)



    C137876E01
  1. Check for foaming or emulsification.
    If foaming or emulsification is identified, bleed the power steering system .



    C137875E01
  1. With the engine idling, measure the fluid level in the fluid reservoir.

  1. Stop the engine.

  1. Wait a few minutes and remeasure the fluid level in the fluid reservoir.

    Maximum fluid level rise:
    5 mm (0.20 in.)

    If a problem is found, bleed the power steering system .

  1. Check the fluid level.



9. INSPECT FOR POWER STEERING FLUID LEAK


10. INSTALL FRONT FENDER APRON SEAL RH


    A162371
  1. Install the front fender apron seal RH with the 2 bolts and clip.



11. INSTALL FRONT WHEEL RH

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }