Home › ENGINE › 2GR-FE FUEL › FUEL INJECTOR

FUEL INJECTOR > INSTALLATION

for Preparation Click here



1. INSTALL FUEL INJECTOR ASSEMBLY


    A129475E01
  1. Apply a light coat of spindle oil or gasoline to new O-rings, and install them to each injector.



    A129476E01
  1. Apply a light coat of spindle oil or gasoline where the fuel delivery pipe contacts the O-ring.

  1. Push the fuel injector while turning it to install the injector in the fuel delivery pipe.

  1. Position the fuel injector connector outward.

    NOTICE:
    1. Be careful not to twist the O-ring.
    2. After installing the fuel injector, check that it turns smoothly. If not, reinstall it with a new O-ring.



    A129472E01
  1. Install 6 new insulators to the intake manifold.



    A129471
  1. Place the fuel delivery pipe which has the 6 fuel injectors installed to it in position on the intake manifold.

    NOTICE:
    Be careful not to drop the fuel injectors when installing the fuel delivery pipe.

  1. Temporarily install the 5 bolts which are used to hold the fuel delivery pipe to the intake manifold.

    NOTICE:
    After installing the fuel injectors, check that they turn smoothly. If not, reinstall the injectors with new O-rings.

  1. Tighten the 5 bolts which are used to hold the fuel delivery pipe to the intake manifold.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



    A137341
  1. Connect the 6 fuel injector connectors.



2. CONNECT FUEL TUBE SUB-ASSEMBLY


    A129477E02
  1. Push in the tube connector onto the pipe until the tube connector makes a "click" sound.

    NOTICE:
    1. Before connecting the tube, make sure that it is not damaged. Make sure that there is no dirt present on the connecting surfaces.
    2. After connecting, check that the fuel tube connector and the pipe are securely connected by pulling on them.

  1. Install the No. 2 fuel pipe clamp.



3. INSTALL INTAKE AIR SURGE TANK ASSEMBLY

NOTICE:
DO NOT apply oil to the bolts listed below:
Tightening Parts
Surge Tank and Intake Manifold
No. 1 Surge Tank Stay and Surge Tank
Throttle Body Bracket and Surge Tank



    A129468E11
  1. Install a new gasket to the intake air surge tank assembly.

  1. Using a 5 mm hexagon socket wrench, install the 4 bolts. (*1)

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Install the intake air surge tank assembly with the 2 nuts and 2 bolts. (*2)

    Torque:
    Nut:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }
    Bolt:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



    A129467
  1. Connect the connector.



    A162431E01
  1. Connect the union to check valve hose. (*1)

  1. Connect the No. 1 ventilation hose. (*2)



    A129464E10
  1. Install the clamp and connect the throttle with motor body assembly connector. (*3)

  1. Connect the vapor feed hose assembly. (*4)

  1. Connect the 2 water by-pass hoses to the throttle with motor body assembly. (*5)



4. INSTALL AIR CLEANER CAP SUB-ASSEMBLY


    A163204
  1. Install the 2 bolts and air cleaner cap sub-assembly.



    A135113E01
  1. Connect the No. 2 ventilation hose and air cleaner hose band.

  1. Connect the vacuum hose (EVAP) to the air cleaner hose.



    A135112E01
  1. Connect the 3 vacuum hoses.



5. ADD ENGINE COOLANT
  1. Tighten the radiator drain cock plug by hand.

  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for cylinder block drain cock plugs

  1. Remove the air drain cock plug from the water inlet housing.



    A162799E01
  1. Loosen the air drain plug at the top of the radiator 3 or 4 turns.

  1. Add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the engine air drain cock hole. Then install the air drain cock plug to the water inlet housing.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for air drain cock plug

  1. Continue to add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the radiator air drain hole. Then close the air drain plug at the top of the radiator.

    HINT:
    If the coolant level at the radiator inlet opening drops after squeezing the No. 1 and No. 2 radiator hoses, add coolant.

  1. Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).

    Standard capacity:
    11.3 liters (12.0 US qts, 10.0 Imp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    2. Contact your TOYOTA dealer for further details.

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Slowly pour coolant into the radiator reservoir tank until it reaches the FULL line.

  1. Squeeze the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level is low, add coolant.

  1. Bleed air from the cooling system.

    1. Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.

      HINT:
      The thermostat open timing can be confirmed by squeezing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.

    2. Maintain the engine speed at 2500 to 3000 rpm.

    3. Squeeze the inlet and outlet radiator hoses several times by hand to bleed air.

      CAUTION:
      When squeezing the radiator hoses:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the radiator fan.

      NOTICE:
      1. Make sure that the radiator reservoir still has some coolant in it.
      2. If the coolant temperature gauge indicates an excessive temperature, turn off the engine and let it cool.
      3. If there is not enough coolant, the engine may overheat or be seriously damaged.
      4. If the radiator reservoir does not have enough coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the FULL line.

  1. Stop the engine and wait until the engine coolant cools down.

  1. Add engine coolant to the FULL line on the radiator reservoir.



6. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


7. INSPECT FOR COOLANT LEAK

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

NOTICE:
Before performing each inspection, turn the A/C switch OFF.



    A161453
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.



8. INSTALL NO. 1 ENGINE UNDER COVER


9. INSPECT FOR FUEL LEAK
  1. Check fuel pump operation.

    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch to ON.

      NOTICE:
      Do not start the engine.

    3. Turn the Techstream main switch on.

    4. Select the following menu items: Power train / Engine and ECT / Active Test / Control the Fuel Pump Speed.

    5. Check for pressure in the fuel inlet tube from the fuel line. Check that sound of fuel flowing in the fuel tank can be heard. If no sound can be heard, check the integration relay, fuel pump, ECM and wiring connector.

  1. Inspect for fuel leaks (*1).

    1. Check that there are no fuel leaks anywhere on the system after performing maintenance. If there is a fuel leak, repair or replace parts as necessary.

  1. Turn the ignition switch off.

  1. Disconnect the Techstream from the DLC3.



10. INSTALL V-BANK COVER SUB-ASSEMBLY


    A162365
  1. Fit the 3 retainers and install the V-bank cover.



11. INSTALL COWL TOP PANEL SUB-ASSEMBLY OUTER FRONT


A162430
  1. Install the 7 bolts and the cowl top panel sub-assembly outer front.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the fuel pump resistor connector.

  1. Connect the wire harness clamp.



12. INSTALL NO. 1 COWL TOP TO COWL BRACE INNER


A162429
  1. Install the 2 bolts and the No.1 cowl top to cowl brace inner.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



13. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


    I035791E01
  1. Install the wiper motor & link assembly with the 4 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Connect the connector.



14. INSTALL FRONT WIPER ARM LH
  1. Operate the wiper, and stop the windshield wiper motor assembly to the automatic stop position.



    E058837E18
  1. Scrape off the serration part of the wiper arm with a round file or equivalent.

  1. Clean the wiper pivot serration with a wire brush.



    I035782E01
  1. Install the front wiper arm LH with the nut to the position shown in the illustration.

    Torque:
    20 N*m{ 204 kgf*cm , 14.8 ft.*lbf }

    HINT:
    Hold down the arm hinge by hand to fasten the nut.



15. INSTALL FRONT WIPER ARM RH
  1. Scrape off the serration part of the wiper arm with a round file or equivalent.

  1. Clean the wiper pivot serration with a wire brush.



    I035783E01
  1. Install the front wiper arm RH with the nut to the position shown in the illustration.

    Torque:
    20 N*m{ 205 kgf*cm , 15 ft.*lbf }

    HINT:
    Hold down the arm hinge by hand to fasten the nut.

  1. Operate the wiper while running the water or the washer fluid over the window, and check the wiping condition and that the front wiper does not hit against the vehicle body.