Home › ENGINE › 2GR-FE FUEL › FUEL INJECTOR

FUEL INJECTOR > REMOVAL

for Preparation Click here



1. DISCHARGE FUEL SYSTEM PRESSURE

HINT:
Click here.



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


3. REMOVE NO. 1 ENGINE UNDER COVER


4. DRAIN ENGINE COOLANT


  1. Loosen the radiator drain cock plug.


    A161473E01

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Remove the radiator cap sub-assembly from the radiator assembly.

    NOTICE:
    Do not remove the radiator cap sub-assembly while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the 2 cylinder block drain cock plugs.



5. REMOVE FRONT WIPER ARM HEAD CAP


    I035789E01
  1. Using a small screwdriver, remove the 2 front wiper arm covers.

    HINT:
    Tape up the screwdriver tip before use.



6. REMOVE FRONT WIPER ARM RH
  1. Operate the wiper, and stop the windshield wiper motor assembly to the automatic stop position.

  1. Remove the nut and the FR wiper arm RH.



7. REMOVE FRONT WIPER ARM LH
  1. Remove the nut and the FR wiper arm LH.



8. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    I035790E01
  1. Remove the 6 claws and the cowl top ventilator louver sub-assembly.



9. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
  1. Disconnect the connector.



    I035791E01
  1. Remove the 4 bolts and wiper motor & link assembly.



10. REMOVE NO. 1 COWL TOP TO COWL BRACE INNER


    A162429
  1. Remove the 2 bolts and the No. 1 cowl top to cowl brace inner.



11. REMOVE COWL TOP PANEL SUB-ASSEMBLY OUTER FRONT


A162430
  1. Remove the wire harness clamp.

  1. Disconnect the fuel pump resistor connector.

  1. Remove the 7 bolts and the cowl top panel outer front.



12. REMOVE V-BANK COVER SUB-ASSEMBLY


    A162365
  1. Hold the front of the V-bank cover and raise it to disengage the 2 clips on the front of the cover. Continue to raise the cover to disengage the clip on the rear of the cover and remove the cover.

    NOTICE:
    Attempting to disengage both front and rear clips at the same time may cause the cover to break.



13. REMOVE AIR CLEANER CAP SUB-ASSEMBLY


    A135112E01
  1. Disconnect the 3 vacuum hoses.



    A135113E01
  1. Remove the No. 2 ventilation hose and air cleaner hose band.

  1. Disconnect the vacuum hose (EVAP) from the air cleaner hose.



    A163204
  1. Remove the 2 bolts and air cleaner cap sub-assembly.



14. REMOVE INTAKE AIR SURGE TANK ASSEMBLY


    A129464E10
  1. Disconnect the 2 water by-pass hoses from the throttle with motor body assembly. (*1)

  1. Disconnect the fuel vapor feed hose assembly.(*2)

  1. Disconnect the throttle with motor body assembly connector and clamp. (*3)



    A162431E01
  1. Disconnect the No. 1 ventilation hose. (*4)

  1. Disconnect the union to check valve hose. (*5)



    A129467
  1. Disconnect the connector.



    A129468E11
  1. Using a 5 mm socket hexagon wrench, remove the 4 bolts. (*1)

  1. Remove the 2 nuts, 2 bolts, and intake air surge tank. (*2)

  1. Remove the gasket from the intake air surge tank.



15. DISCONNECT FUEL TUBE SUB-ASSEMBLY


    A129469E02
  1. Remove the No. 2 fuel pipe clamp.

  1. Pinch the tube connector and pull out the fuel pipe.

    NOTICE:
    1. Check that there is no dirt or other foreign objects around the connector before disconnecting it. Clean the connector as necessary.
    2. It is necessary to prevent mud or dirt from entering the quick connector. If mud or dirt gets in the connector, the O-rings may not seal properly.
    3. Only disconnect the quick connector by hand.
    4. Do not bend, kink or twist the nylon tubes. Protect the connector by covering it with a plastic bag.
    5. If the pipe and the connector are stuck, carefully try wiggling or pushing and pulling on the connector to release it. Pull the connector off the pipe carefully.



16. REMOVE FUEL INJECTOR ASSEMBLY


    A137341
  1. Disconnect the 6 fuel injector connectors.



    A129471
  1. Remove the 5 bolts and fuel delivery pipe sub-assembly together with the 6 fuel injectors.

    NOTICE:
    Be careful not to drop the fuel injectors when removing the fuel delivery pipe sub-assembly.



    A129472E01
  1. Remove the 6 injector vibration insulators from the intake manifold.



    A129473
  1. Pull out the fuel injectors from the fuel delivery pipe sub-assembly.



    A129475E02
  1. Remove the 6 O-rings from the fuel injectors.