Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > Brake Warning Light Remains ON

for Preparation Click here


DESCRIPTION

The BRAKE warning light comes on when the brake fluid is insufficient, the parking brake is applied or the EBD is defective.

WIRING DIAGRAM


C160966E02


INSPECTION PROCEDURE

HINT:
When releasing the parking brake, move the shift lever into the P position in an AT vehicle, and choke in an MT vehicle to hold the vehicle for safety.

1.CHECK BRAKE FLUID LEVEL
  1. Check that the brake fluid level is proper.



NG
ADD BRAKE FLUID
OK


2.CHECK DTC
  1. Are the DTC recorded? (Click here)


Result:

Result
Proceed to
DTC is output
A
DTC is not output
B



B
Go to step 3
A

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS 

3.CHECK BRAKE WARNING LIGHT
  1. WHEN USING TECHSTREAM:

    1. Connect Techstream to the DLC3.

    2. Start the engine.

    3. Select the item "Brake Warning Light" in the Active Test and operate the BRAKE warning light on Techstream.

      ABS / VSC / TRAC: 
      Tester Display
      Test Part
      Control Range
      Diagnostic Note
      Brake Warning Light
      BRAKE warning light
      Warning light ON / OFF
      Observe combination meter

    4. Check that "ON" and "OFF" of the BRAKE warning light are indicated on the combination meter when using Techstream.

      OK:
      Turn the BRAKE warning light on or off in accordance with Techstream.



  1. WHEN NOT USING TECHSTREAM:

    1. Turn the ignition switch off and disconnect the connector from the skid control ECU.



    2. G024767E52
    3. Ground terminal BRL of the skid control ECU.

    4. Turn the ignition switch to the ON position.

    5. Check that the brake warning light.

      OK:
      Turn the light on or off in accordance with the connection of terminal GND and BRL.

      NOTICE:
      When replacing the brake actuator assembly, perform zero point calibration (Click here).



NG
Go to step 4
OK

REPLACE BRAKE ACTUATOR ASSEMBLY 

4.INSPECT PARKING BRAKE SWITCH
  1. Remove the parking brake switch connector.



    G026238E11
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    P6-1 - Ground part
    Released
    Below 1 Ω
    P6-1 - Ground part
    Pushed in
    10 kΩ or higher



NG
REPLACE PARKING BRAKE SWITCH
OK


5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - PARKING BRAKE SWITCH)
  1. Disconnect the skid control ECU connector and the parking brake switch connector.



    G026243E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    S3-28 (PKB) - P6-1 (PKB)
    Below 1 Ω

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    S3-28 (PKB) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT BRAKE FLUID LEVEL WARNING SWITCH
  1. Remove the reservoir tank cap and strainer.

  1. Disconnect the brake fluid level warning switch connector.



    C119428E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    (B1-1) - (B1-2)
    Float UP
    10 kΩ or higher
    (B1-1) - (B1-2)
    Float DOWN
    Below 1 Ω



NG
REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY (BRAKE FLUID LEVEL WARNING SWITCH)
OK


7.CHECK HARNESS AND CONNECTOR (BRAKE FLUID LEVEL WARNING SWITCH - COMBINATION METER)
  1. Disconnect the combination meter connector and the brake fluid level warning switch connector.



    C119429E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    (C10-13) - (B1-1)
    Below 1 Ω

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    (C10-13) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE COMBINATION METER ASSEMBLY